新手上路
快意人生
- 舊站積分
- 4
- 舊站發表文章數
- 494
|
發表於 2005-3-29 19:10:59
|
顯示全部樓層
來響應一下Alan兄..po上一篇國外的介紹DAT文章
DAT RECORDERS !
The DAT (Digital Audio Tape) recorder is a great format to work in. It delivers CD-quality sound (or better) in a small, tape-based format. And, since DAT has become a mastering and audio backup standard, it's easy to exchange tapes with other studios and musicians.
The older-style analog tape recorders degrade the audio they record. They add tape hiss, tape distortion, frequency response errors, and speed variations (wow and flutter). Digital recorders get rid of these problems. Thanks to digital recording, the original goal of tape recording has finally been achieved: to accurately store and reproduce our audio creations.
In this booklet we'll give a brief overview of digital recording, DAT recorders, DAT tape, and digital editing.
--------------------------------------------------------------------------------
DIGITAL RECORDING
Like an analog tape recorder, a digital recorder (such as a DAT machine) records audio on magnetic tape, but in a different way. Here's what happens.
The signal from your mixer is run through a lowpass filter (anti- aliasing filter) which removes all frequencies above 20 kHz.
Next, the filtered signal passes through an analog-to-digital (A/D) converter. This converter measures the voltage of the audio waveform several thousand times a second.
Each time the waveform is measured, a binary number (made of 1's and 0's) is generated that represents the voltage of the waveform at the instant it is measured. Each 1 and 0 is called a bit, which stands for binary digit.
These binary numbers are stored magnetically on tape in the form of a modulated square wave recorded at maximum level.
The playback process is the reverse:
The binary numbers are read from tape.
The digital-to-analog (D/A) converter translates the numbers back into an analog signal made of voltage steps.
An anti-imaging filter (lowpass filter) smooths the steps in the analog signal, resulting in the original analog signal.
Since the digital playback head reads only two binary numbers, it is insensitive to tape hiss and tape distortion. Numbers are read into a buffer memory and read out at a constant rate, eliminating speed variations.
The resulting freedom from noise, distortion, print- through, wow, and flutter makes digital recordings sound extremely clean and clear. Unlike analog recordings, digital recordings can be copied with little or no degradation in quality. Lost data is restored by error-correction circuitry.
QUANTIZATION
As we said, the audio signal is measured several thousand times a second to generate a string of binary numbers. The longer each binary number is (the more bits it has), the greater the accuracy of the measurement. In other words, short binary numbers provide poor resolution of the waveform's amplitude or voltage; long binary numbers provide good resolution. A quantization of 16 bits is considered to be adequate for high-fidelity reproduction. It is the current standard for digital tape recording and compact discs.
SAMPLING RATE
The rate at which the waveform is measured is called the sampling rate, measured in samples/sec. At a sampling rate of 48 kHz, 48,000 measurements are generated for each second of sound.
The higher the sampling rate, the wider the frequency response of the recording. The upper frequency limit is slightly less than half the sampling rate. If the sampling rate is 44.1 kHz, this is adequate for high-fidelity reproduction up to 20 kHz.
--------------------------------------------------------------------------------
DAT RECORDERS
Currently, open-reel digital recorders are quite expensive. For stereo mastering, there's an alternative to an open-reel digital recorder: a DAT or R-DAT (Rotating-head Digital Audio Tape) Recorder. Costing $700 and up, a DAT recorder records audio digitally on a small cassette. Its sound quality is at least as good as a compact disc. What you put in, you get out, virtually without any added hiss, distortion, or wow & flutter.
The DAT transport is very fast. A two-hour tape winds in about 45 seconds. The DAT machine records on a small cassette about half the size of a standard analog cassette. The shell has a hinged door that flips open to expose the tape.
When you load the cassette, two spindles enter the two hubs from below the cassette and lock it into place. Then the tape is drawn into the machine and wraps around a rotating drum, which holds the record and playback heads.
As the tape moves past the rotating heads, they scan diagonally across the tape as they write the digital signal. The tracks laid down by the rotating heads are about one-tenth the thickness of a human hair! Although the linear tape speed is slow, the tape speed as seen by the record head is very high, so the ultrasonic digital signal can be recorded. Tape drop-outs can cause data losses, but most of these are restored by a circuit that corrects the errors.
While the audio program is recorded, absolute time is written on tape. It's the running time in hours, minutes, and seconds, where 00:00:00 is at the head of the tape. You use it to locate selections and time them.
--------------------------------------------------------------------------------
DAT TAPE
As we said, a DAT cassette is about half the size of a standard analog cassette, measuring 73 x 54 x 10.5 mm. Its tape is 3.81 millimeters (1/8") wide. On one end of the shell is a hinged door that flips open to expose the tape so it can be drawn around the rotating head drum.
DAT tapes can record up to two hours of audio on a tape about 60 meters long. They come in various lengths. Blank tapes use a metal-powder oxide, while prerecorded tapes use a barium-ferrite oxide. The cassette includes a sliding safety tab on one end to prevent accidental erasure. If the little door is closed, you can record on the tape. If it's open, you can't.
Computer-grade DAT tapes are more reliable than audio-grade DAT tapes. They were originally designed for computer backup systems but make an excellent audio recording tape. They use a different formulation, run cleaner are easier on your heads and are certified error free.
SUBCODES
Subcodes are information written on tape, independent of the audio signal, that tells the machine the number of each selection or program, where each selection starts, and whether or not to play each one. You can record or erase subcodes without affecting the audio program. The three main types of subcodes are Program Numbers, Start IDs, and Skip IDs.
* Program Numbers are assigned to selections in order, and can then be used to locate them.
* A Start ID marks the beginning of each selection. It can be written manually or automatically. Manual Start IDs can be placed anywhere, say, to mark cues. Automatic Start IDs are put on tape whenever there is enough signal applied, after a silence of three or more seconds. You'll want to record manual Start IDs after recording all your mixes onto a DAT tape.
Like other subcodes, Start IDs can be recorded or erased without altering the audio program. You can enter them during recording or playback. If the cassette's safety tab is set to prevent accidental erasure, you can't record or erase subcodes. Most DAT machines can automatically re-number the Start IDs in consecutive order.
*A Skip ID makes the machine skip the selection. This ID can only be written manually. Whenever the machine senses a Skip ID during playback, it stops and fast winds to the next Start ID, and begins playing. This function can be turned on and off. |
|