忘記密碼
 立即註冊
查看: 934|回覆: 2

分享唱臂廠商對臂管高度的看法,之一

[複製鏈接]

44

主題

164

回帖

0

積分

新手上路

二星級會員

舊站積分
461
舊站發表文章數
208
發表於 2016-12-29 10:42:31 | 顯示全部樓層 |閱讀模式
這是一段時間前,我在寫 Viv Lab Rigid Float 超短臂評論時有疑問,請唱臂的主人去問設計者,得到的回答。為了保護隱私,我將朋友的資料移除。

幾個他說的重點:

如果臂管太陡,向唱頭斜下去,可以

1)就這樣用,因為刻片機刻片時的角度設定就超過垂直。而且,斜4度可能音質最好。

2)如果這樣用有卡到的問題(例如:我遇到唱頭放下去到不了唱片的情況),那就在唱頭與唱頭蓋之間加墊片。石墨(我想他指的是碳纖維)是最好的材質。


寄件人: "Koichiro Akimoto, ViV lab." <koichiro@vivaudiolab.com>
日期: 2016年6月22日 GMT+8 下午8:37:33
收件人: /////////////
標題: Re: Viv tonearm problem

Dear Mr. /////,

I hope this finds you well.
Thank you for using Rigid Float. When the arm is too high, you have two options as below.

1. Use as it is (i.e. headshell is lower than pivot). There is no problem in such position because the setting of cutting machine  is like that, not just vertical. It is said that sound quality is the best when the arm pipe has the angle of 4 degree.

2. Put a spacer tip (6mm thickness) between the headshell and the cartridge. Carbon is the best for the material of the spacer.

I hope you will satisfy with Rigid Float.

Best regards,

==============
2016/06/22 11:34、
To whom may concern
Hi
I am ///// . Had bought Viv 7" tonearm . I got problem with setting up this tonearm because it is too high for my turntable both immedia rpm 2. And Transroter  orfero . I had to put at least 6mm record mat to get it right . For transroter is ok ,but for immedia the locking record clamp can not work . Do you have any idea to solve this issue.?

44

主題

164

回帖

0

積分

新手上路

二星級會員

舊站積分
461
舊站發表文章數
208
 樓主| 發表於 2016-12-29 15:20:13 | 顯示全部樓層

Re: 分享唱臂廠商對臂管高度的看法,之一

忘了說,如果有翻譯成中文的需要,請私訊。



QUOTE]原發表者是 brtsai
[B]這是一段時間前,我在寫 Viv Lab Rigid Float 短臂評論時有疑問,請唱臂的主人去問設計者,得到的回答。為了保護隱私,我將朋友的資料移除。

寄件人: "Koichiro Akimoto, ViV lab." <koichiro@vivaudiolab.com>
日期: 2016年6月22日 GMT+8 下午8:37:33
收件人: /////////////
標題: Re: Viv tonearm problem

Dear Mr. /////,

I hope this finds you well.
Thank you for using Rigid Float. When the arm is too high, you have two options as below.

1. Use as it is (i.e. headshell is lower than pivot). There is no problem in such position because the setting of cutting machine  is like that, not just vertical. It is said that sound quality is the best when the arm pipe has the angle of 4 degree.

2. Put a spacer tip (6mm thickness) between the headshell and the cartridge. Carbon is the best for the material of the spacer.

I hope you will satisfy with Rigid Float.

Best regards,

==============
2016/06/22 11:34、
To whom may concern
Hi
I am ///// . Had bought Viv 7" tonearm . I got problem with setting up this tonearm because it is too high for my turntable both immedia rpm 2. And Transroter  orfero . I had to put at least 6mm record mat to get it right . For transroter is ok ,but for immedia the locking record clamp can not work . Do you have any idea to solve this issue.? [/B][/QUOTE]

44

主題

164

回帖

0

積分

新手上路

二星級會員

舊站積分
461
舊站發表文章數
208
 樓主| 發表於 2016-12-30 11:31:53 | 顯示全部樓層

Re: 分享唱臂廠商對臂管角度的看法,之一

幾個他說的重點:

如果臂管太陡,向唱頭斜下去,可以

1)就這樣用,因為刻片機刻片時的角度設定就超過垂直。而且,斜4度可能音質最好。

2)如果這樣用有卡到的問題(例如:我遇到唱頭放下去到不了唱片的情況),那就在唱頭與唱頭蓋之間加墊片。石墨(我想他指的是碳纖維)是最好的材質。

原發表者是 brtsai
[B]這是一段時間前,我在寫 Viv Lab Rigid Float 短臂評論時有疑問,請唱臂的主人去問設計者,得到的回答。為了保護隱私,我將朋友的資料移除。

寄件人: "Koichiro Akimoto, ViV lab." <koichiro@vivaudiolab.com>
日期: 2016年6月22日 GMT+8 下午8:37:33
收件人: /////////////
標題: Re: Viv tonearm problem

Dear Mr. /////,

I hope this finds you well.
Thank you for using Rigid Float. When the arm is too high, you have two options as below.

1. Use as it is (i.e. headshell is lower than pivot). There is no problem in such position because the setting of cutting machine  is like that, not just vertical. It is said that sound quality is the best when the arm pipe has the angle of 4 degree.

2. Put a spacer tip (6mm thickness) between the headshell and the cartridge. Carbon is the best for the material of the spacer.

I hope you will satisfy with Rigid Float.

Best regards,

==============
2016/06/22 11:34、
To whom may concern
Hi
I am ///// . Had bought Viv 7" tonearm . I got problem with setting up this tonearm because it is too high for my turntable both immedia rpm 2. And Transroter  orfero . I had to put at least 6mm record mat to get it right . For transroter is ok ,but for immedia the locking record clamp can not work . Do you have any idea to solve this issue.? [/B]
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-19 21:15 , Processed in 0.035125 second(s), 28 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表