忘記密碼
 立即註冊
查看: 1572|回覆: 9

JL W7 閉笭腴秞 ^^

  [複製鏈接]

11

主題

32

回帖

0

積分

新手上路

初級會員

舊站積分
0
舊站發表文章數
43
發表於 2002-5-3 02:13:50 | 顯示全部樓層 |閱讀模式
帶朋友去敗家的感想

朋友的
主機歌樂9675
前rainbow 265 p3
前擴大JL 300.2
重低音JL W7 12
後擴大JL 500.1
我的
主機Alpine 7990R
前Rainbow 265 P3
前擴大ZapCo 2.0
重低音JL W3 D2*2
後擴大ZapCo 3.0
改全平衡輸出七段EQ

在朋友的車上聽鼓聲…
在很多的鼓聲中有一支腳踏鼓從很遠的地方傳來,且定位清楚…聲音很棒
但在我的車上卻發覺…那支鼓變得很近且定位不清…有點感覺不到它的存在
(八、九個音響店老闆一起聽…^^不過…當然是輪流的囉…)

很多低音在朋友車上覺得很深很沈…
JL W7 我覺得開創了重低音的里程碑…

細節部份我說不清楚…但感覺真的很明顯…對了…我和朋友的車都經由中華音響協會理事長調過音…

反正我就覺得這支重低音…真的能夠比較真實的表現出一些原音重現的感覺
純分享…謝謝

23

主題

272

回帖

0

積分

新手上路

二星級會員

舊站積分
20
舊站發表文章數
295
發表於 2002-5-3 08:35:21 | 顯示全部樓層

Re: JL W7 讓我覺得…又想敗家了

500.1還沒有完全發揮W7的潛力喔...

那顆W7是12W7 or 13W7? 裝箱方式是密閉式或通氣式? 容積多少?

33

主題

591

回帖

0

積分

新手上路

如果讓我看到夢寐以求的畫面,我

舊站積分
6
舊站發表文章數
621
發表於 2002-5-3 10:55:21 | 顯示全部樓層
我也想要重整我的超低音系統,
現在比較傾向於做 Box + 快拆...
JL 的超低音單體一向給人一種 "Legend" 的感覺,
Adam 你熟嗎?! 多聊聊這些事吧

他們自家出的後級聲音不知道怎麼樣喔,
昨天收到網友的 E-mail, 說 CarSound 的 Richard Clark 說 Amplifier dont's make any difference in Sound Quality. 不知道你覺得如何呢?

23

主題

272

回帖

0

積分

新手上路

二星級會員

舊站積分
20
舊站發表文章數
295
發表於 2002-5-3 14:23:11 | 顯示全部樓層
JL直到出了W7我才比較注意,12W7是雙音圈1.5歐姆的單體。


因為結構特殊,安裝方面另有網頁介紹

JL W7 安裝方法

至於RC的這個理論在美國已經爭吵了好多年了,幾年前我也有提出Richard Clark's $10000 Amp Challenge在友站討論。

這樣好了,把他的理論po到家用發燒音響區,看看諸位家用網友對這個看法的意見如何...將會非常有爭議性...

23

主題

272

回帖

0

積分

新手上路

二星級會員

舊站積分
20
舊站發表文章數
295
發表於 2002-5-3 14:29:41 | 顯示全部樓層

THE $10,000 AMPLIFIER CHALLENGE RULES Part I {April 21, 2000}

There is no question that all amps are not the same. It is very easy to
measure large differences in the performance of amplifiers. This is true in
nearly every known specification, including power, noise, distortion, etc.
My experience has led me to believe that even though these differences can
be easily measured, hearing those differences may not be so easy. Given the
relatively small magnitude of performance differences, there is a giant step
between amplifier performance and our ability to hear performance
differences.
It is claimed by designers, manufacturers and especially salespersons
that differences in amplifiers are clearly audible. Reasons include
"obvious" advantages of one type of circuit topology over another. For
example, it is claimed that certain designs have a smoother midrange
response whereas other amplifiers exhibit tighter bass. Tube fanatics claim
that tube amplifiers have that "warm" sound we all need in our systems.
Such descriptive terms are certainly subject to personal
interpretation. It is not my intention to determine if one particular
amplifier is better than another amplifier. Differences in the quality of
the discrete components and constructions are more appropriate for settling
the issue of "good - better - best." The sole purpose of my amplifier
challenge is to determine if the differences in amplifiers are audible.

What differences are Audible?

I believe the perceived differences in amplifiers are all due to
various factors that can be explained with basic physics and elementary
psychoacoustics. For instance, if two amplifiers are not carefully matched
in volume, and one amp is slightly louder than the other, then it would be a
simple matter to detect such a difference. In such an example it is
important to understand that it is not the circuit topology, quality of the
component, design excellence, or superb marketing and packaging that caused
the noticeable difference - it was an error in the test setup! It is my
present belief that as long as a modern amplifier is operated within its
linear range (below overload), the differences between amps are inaudible to
the human ear.

Comparing Amps

The idea here is for a test subject to scientifically demonstrate
his/her ability to hear differences in amplifiers. It is our job to
carefully match the amps so that we are comparing "apples to apples" instead
of "oranges to frogs." This means that we sure wouldn't want to compare one
amplifier that had + 12 dB of high frequency boost against another amplifier
that was adjusted for + 12 dB of bass boost. Such a test would be easy to
pass - even on identical amplifiers with consecutive serial numbers.
For our comparison test, we aren't concerned with which amplifier
sounds best to the test subject. We only require that the listener be able
to identify each amplifier when it is powering the speakers. Since many
folks seem to believe that amplifiers have some kind of distinctive sonic
character, this test should be easy to pass. Right? After all, we're talking
about comparing those harsh sounding, high distortion, squeaky "widget As"
to those warm sounding, smooth, bass hog "widget Bs."
Now pay particular attention to the following sections. Since we're
looking for differences in amplifiers, and we already know that those
differences are probably going to be very, very small, it is important that
the parameters under our control be carefully adjusted so as to be equal as
possible. This means that we must be cognizant of differences we might
unknowingly introduce between amp A and amp B. They must be adjusted as
identical as possible. We already mentioned the importance of volume. The
same goes for the L and R balance. It sure would be easy to choose an
amplifier that exhibited left side bias over a balanced amp. Right?
Well, in order to keep this amplifier comparison test fair, there are a
few other parameters that must be considered. I'll list them all in the
following section.

23

主題

272

回帖

0

積分

新手上路

二星級會員

舊站積分
20
舊站發表文章數
295
發表於 2002-5-3 14:30:59 | 顯示全部樓層

THE $10,000 AMPLIFIER CHALLENGE RULES Part II {April 21, 2000}

Amplifier Comparison Test Conditions

1. Amplifier gain controls - of both channels - are matched to within +- .05
dB.

2. Speaker wires on both amps are properly wired with respect to polarity.
(+ and -)

3. That neither amp has signal phase inversion. If so correction will be
made in #2 above.

4. That neither amp is loaded beyond its rated impedance.

5. That all amplifiers with signal processors have those circuits bypassed.
This includes bass boost circuits, filters, etc. If frequency tailoring
circuits cannot be completely bypassed an equalizer will be inserted in the
signal path of one (only one and the listener can decide which) of the amps
to compensate for the difference. Compensation will also be made for input
and output loading that affects frequency response. Since we are only
listening for differences in the sonic signature of circuit topology, the
addition of an EQ in one signal path only should make the test even easier.

6. That neither amp exhibits excessive noise (including RFI).

7. That each amp can be properly driven by the test setup. Not normally a
problem but it is theoretically a problem.

8. That the L and R channels are not reversed in one amp.

9. That neither amp has excessive physical noise or other indicators that
can be observed by the listener.

10. That neither amp has DC OFFSET that causes audible pops when its output
is switched.

11. That the channel separation of all amps in the test is at least 30 dB
from 20Hz to 20kHz.



In addition to these requirements the test will be conducted according to
the following rules.

Amplifier Test Comparison Rules

1. To make things easy we would prefer to use high quality home type
loudspeakers for the test. If our speakers are not acceptable, the listener
can provide any commercially available speaker system as long as it uses
dynamic drivers. The actual measured impedance cannot exceed the rated load
impedance of the amplifiers tested. If, however, the tester would like to
perform the test in a car, we will use a car, however, it will have to be
provided by the test subject. For practicality we will have to limit the
number of amplifier channels to four or less.

2. Amplifiers will be powered from the same power supply at a nominal 14
volts DC. (any voltage is OK as long as it is the same for both amps)

3. The test can be conducted at any volume desired; however, the amps will
not be allowed to clip. In other words, listening volume can not exceed the
power capacity of the smallest amp of the pair being tested. (power capacity
will be defined as clipping or 2%THD 20Hz to 10kHz, whichever is less)

4. No test signals can be used - only commercially available music.

5. The listener can compare two amps at a time for as long as desired. For
practical reasons we would like to keep this at least no more than a few
hours. A test session will consist of 12 A/B sequences. Passing the test
will require a positive identification of each amp for all 12 sequences.
Remember, guessing will get you about 6 out of 12. If the differences are so
great, and a subject can really hear the difference, then he/she should be
able to do so for all 12 sequences.

6. To win the $10,000.00, the listener must pass two complete sessions of 12
comparisons. Passing the test means 24 correct responses.* The amp of choice
can be compared to the same or a different amp in each session - challengers
choice. We have many amplifiers in our demo inventory such as, but not
limited to, Alpine, Rockford, Kicker, Phoenix Gold, Precision Power, MTX,
Adcom, Kenwood, Pioneer, Sony, etc. You can pick any of them or bring your
own.

7. All amps must be brand name, standard production, linear voltage
amplifiers. This does not exclude high current amps. Amps can not be
modified and must meet factory specs. They must be "car audio amplifiers
designed to be powered from a car's electrical system."

8. Failure of an amp (this includes thermal shutdown) during the test will
require that the test be repeated after repair or replacement or cooling of
the amp. This means that the entire test session will have to be repeated.

9. The amps will not be overloaded during the session from either a voltage
or current requirement.

10. To save time the listener will have to pass a quick 8 trial session to
qualify for the extended 2 session test for the money prize. Any 2 amps can
be used for this test. Passing this qualifying test will require at least 6
out of 8 correct answers.

11. The amplifier power up and/or power down sequence will not be acceptable
for comparison. (The turn on/off noises of some amplifiers would give it
away.)

12. Although anyone is welcome to take the test, only subjects employed in
the car audio industry or Car Sound subscribers are eligible for the
$10,000.00 prize.

13. Cost to take the test is $100.00. $300.00 for people representing
companies. Payable in advance, scheduled appointments only. Done correctly
the test takes several hours and I don't have the time if you aren't
serious.

* Twelve correct responses in a row is certainly a lot of correct listening
but $10,000 is also a lot of money for a few hours of easy listening. The
way people describe the differences is that they are like night and day. I
would certainly not have any trouble choosing between an apple and an orange
12 times in a row. When compared fairly I believe the differences in amps
are much too small to audibly detect and certainly too small to pay large
sums of extra money for. If I am wrong someone should be able to carefully
take this test and win my money. Even if I am right, if enough people take
the test eventually someone will take my money due to random chance. This is
the reason for the large sample requirement. If you feel that you can easily
pass this test but 12 sequences will give you "listening fatigue" I am
willing to modify the requirements. Since the way it is being offered is a
challenge and only my money is at risk I am willing to let a confident
challenger "put his money where his ears are". If we are willing to make
this a bet instead of a challenge, I am willing to drop 1 sequence for every
thousand dollars put up by the challenger against my money. This would mean:


____My___________ _ _Your________Trails Required to
win__
$10,000 to $0 =
12 Tries
$9,000 to $1,000 =
11 Tries
$8,000 to $2,000 =
10 Tries
$7,000 to $3,000 =
9 Tries
$6,000 to $4,000 =
8 Tries
$5,000 to $5,000 =
7 Tries
$4,000 to $6,000 =
6 Tries

I will not do the test with less than 6 trails. It would be statistically
meaningless and reduce the challenge to mere gambling.

33

主題

591

回帖

0

積分

新手上路

如果讓我看到夢寐以求的畫面,我

舊站積分
6
舊站發表文章數
621
發表於 2002-5-3 15:44:23 | 顯示全部樓層
My God, 這一大串葡萄可真的需要點時間來好好消化,

這下子我體會到我自己寫一大串時, 看的人的痛苦了... >__<~
可是我又覺得沒寫那麼多, 講的又不清楚,
唉... 可惜小時候作文班都不用功... []

11

主題

32

回帖

0

積分

新手上路

初級會員

舊站積分
0
舊站發表文章數
43
 樓主| 發表於 2002-5-8 00:43:09 | 顯示全部樓層
密閉式  容積34

12W7 可是我朋友的是單音圈
13w7才是雙音圈吧
先大的總經理說的  ^^
買500.1是因為JL 1000.1還在電檢中 ~

11

主題

32

回帖

0

積分

新手上路

初級會員

舊站積分
0
舊站發表文章數
43
 樓主| 發表於 2002-5-8 00:44:07 | 顯示全部樓層
它們的後級力道很夠,但音質部份就…~~~~~~~~~

23

主題

272

回帖

0

積分

新手上路

二星級會員

舊站積分
20
舊站發表文章數
295
發表於 2002-5-8 08:57:32 | 顯示全部樓層
原發表者是 matrox
[B]12W7 可是我朋友的是單音圈
13w7才是雙音圈吧
[/B]


應該是我搞反了吧。[]
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-20 00:46 , Processed in 0.065486 second(s), 42 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表