忘記密碼
 立即註冊
查看: 3470|回覆: 12

擴大機+重低音分頻點

[複製鏈接]

421

主題

2490

回帖

50

積分

新手上路

四星級會員

舊站積分
246
舊站發表文章數
1631
發表於 2010-5-1 00:50:02 | 顯示全部樓層 |閱讀模式
1.兩者要調一樣
2.主動式重低音分頻點調最大 給環擴去做分頻
3.環擴分頻點調最大 給主動式重低音去做分頻

請問何者正確

120

主題

4041

回帖

0

積分

新手上路

頂上雕刻師

舊站積分
261
舊站發表文章數
3097
發表於 2010-5-1 09:00:11 | 顯示全部樓層
要看重低音跟環擴的等級
若分頻切完後,聽聽看重低音發出的聲音,以80hz以下為例,切完後重低音不應該還會唱歌

249

主題

3萬

回帖

220

積分

新手上路

上將

舊站積分
11603
舊站發表文章數
26283
發表於 2010-5-1 11:16:51 | 顯示全部樓層
2............................
[url=http://www.myav.com.tw/market/showthread.php?s=&threadid=5991]進口超值--色差、同軸數位、S線[/url] [url=http://www.myav.com.tw/market/showthread.php?s=&threadid=127614]綜合商品區[/url] [url=http://www.myav.com.tw/market/showthread.php?s=&threadid=20459395]In-akustik 德國敏力線[/url]

148

主題

3757

回帖

240

積分

新手上路

五星級會員

舊站積分
4615
舊站發表文章數
3354
發表於 2010-5-1 11:58:44 | 顯示全部樓層

Re: 擴大機+重低音分頻點

原發表者是 segawar
[B]1.兩者要調一樣
2.主動式重低音分頻點調最大 給環擴去做分頻
3.環擴分頻點調最大 給主動式重低音去做分頻

請問何者正確 [/B]

產品說明書沒寫嗎?還是從來不看?
音樂性是用音響性釀的酒;電影的現場不在電影院,音樂的現場不在音樂廳

421

主題

2490

回帖

50

積分

新手上路

四星級會員

舊站積分
246
舊站發表文章數
1631
 樓主| 發表於 2010-5-1 14:21:45 | 顯示全部樓層

Re: Re: 擴大機+重低音分頻點

原發表者是 ashinn
[B]
產品說明書沒寫嗎?還是從來不看? [/B]

說明書翻爛了
上面沒有寫

另感謝回覆的大大
各加三分答謝

12

主題

43

回帖

0

積分

新手上路

一星級會員

舊站積分
3
舊站發表文章數
53
發表於 2010-5-3 01:24:06 | 顯示全部樓層

Re: 擴大機+重低音分頻點

原發表者是 segawar
[B]1.兩者要調一樣
2.主動式重低音分頻點調最大 給環擴去做分頻
3.環擴分頻點調最大 給主動式重低音去做分頻

請問何者正確 [/B]


我所知道AV主動式的正確  2.主動式重低音分頻點調最大 給環擴去做分頻
但若要細分還要看連接方式,大致有兩種:
A.一般都適用Line-level input就是所謂的 線性電平輸入,目前一般AV主動式重低音,都是採用此法連接.所以答案為2.主動式重低音分頻點調最大 給環擴去做分頻
B.使用 Speaker level input 揚聲器電平輸入,此時答案就是3.環擴分頻點調最大 給主動式重低音去做分頻,此時重低音上的低通濾波開關必須設定為 IN(如果你的重低音背板上有這開關的話).

148

主題

3757

回帖

240

積分

新手上路

五星級會員

舊站積分
4615
舊站發表文章數
3354
發表於 2010-5-3 08:09:58 | 顯示全部樓層
原發表者是 segawar
[B]
說明書翻爛了
上面沒有寫

另感謝回覆的大大
各加三分答謝 [/B]

只有翻當然不行,手到之外還要眼到心到...SB12+ 說明書第 9~10 頁:
Crossover Frequency.  If you use your DD/DTS eceiver/processor's internal crossover to manage bass frequencies (highly recommended) , the setting of this knob on the sub is irrelevant.  (Note: Use the sub's crossover "Enable/Disable" switch discussed below to take advantage of this configuration.)  Otherwise this knob is used to best blend your subwoofer into your other speakers.  Typically used in stereo only systems today.

Crossover enable switch.  If you allow your DD/DTS surround-sound receiver or processor to manage bass frequencies (again, highly recommended), this switch should be set to "Disabled", eliminating the effects of the  "Crossover Frequency" knob and allowing your sub to reproduce just what it's fed from the receiver.  If you use the sub in a two channel (stereo only) configuration, then "Enable" the crossover and adjust the knob to best blend the sub into the output of your speakers.
音樂性是用音響性釀的酒;電影的現場不在電影院,音樂的現場不在音樂廳

421

主題

2490

回帖

50

積分

新手上路

四星級會員

舊站積分
246
舊站發表文章數
1631
 樓主| 發表於 2010-5-3 10:54:47 | 顯示全部樓層
原發表者是 ashinn
[B]
只有翻當然不行,手到之外還要眼到心到...SB12+ 說明書第 9~10 頁:
Crossover Frequency.  If you use your DD/DTS eceiver/processor's internal crossover to manage bass frequencies (highly recommended) , the setting of this knob on the sub is irrelevant.  (Note: Use the sub's crossover "Enable/Disable" switch discussed below to take advantage of this configuration.)  Otherwise this knob is used to best blend your subwoofer into your other speakers.  Typically used in stereo only systems today.

Crossover enable switch.  If you allow your DD/DTS surround-sound receiver or processor to manage bass frequencies (again, highly recommended), this switch should be set to "Disabled", eliminating the effects of the  "Crossover Frequency" knob and allowing your sub to reproduce just what it's fed from the receiver.  If you use the sub in a two channel (stereo only) configuration, then "Enable" the crossover and adjust the knob to best blend the sub into the output of your speakers. [/B]


原來svs有說明書
我重低音買來沒給我說明書阿

421

主題

2490

回帖

50

積分

新手上路

四星級會員

舊站積分
246
舊站發表文章數
1631
 樓主| 發表於 2010-5-3 11:02:08 | 顯示全部樓層

說明書

有人有PB-12NSD的說明書嗎
借我影印一份
電子檔也可以
小弟加三分答謝

148

主題

3757

回帖

240

積分

新手上路

五星級會員

舊站積分
4615
舊站發表文章數
3354
發表於 2010-5-3 12:30:11 | 顯示全部樓層
Velodyne:(FSX-12 Owner's Manual 4~5 頁)
Low-pass crossover- 40 to 120Hz
All inputs sum the left and right channels together, with the resulting signal passing through an adjustable low-pass crossover before being amplified. The crossover control allows you to adjust the upper limit of the subwoofer's frequency response from 40 to 120Hz. The subwoofer's response will begin rolling off above the frequency you set this control to. You should set the crossover frequency to obtain a smooth and seamless transition from the subwoofer to the main speakers in your system. If your main speakers are smaller units with limited low frequency output, you may wish to choose a higher frequency (such as 100-120Hz) than you would with larger speakers which have greater low frequency output. With larger speakers, you might start with this control set lower, such as 80Hz.

A bypass switch is also provided if you wish to use an external crossover. If you are not using an external crossover, we recommend that you use the one provided within the unit for optimum performance!

Subwoofer Direct switch- In/Out
This switch allows the electronic crossover circuitry to be removed from the signal path. This is required in certain installations which route the signal through external processors with a crossover circuit of their own, such as the new digital units. Simply move the switch to OUT to disengage the built in crossover. For all other installations which do not have a separate electronic crossover we recommend you leave the internal crossover  IN  to provide optimum performance.
音樂性是用音響性釀的酒;電影的現場不在電影院,音樂的現場不在音樂廳
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-22 20:42 , Processed in 0.045559 second(s), 42 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表