新手上路
四星級會員
- 舊站積分
- 66
- 舊站發表文章數
- 1298
|
發表於 2001-5-2 12:49:01
|
顯示全部樓層
三槍內投影電視的微調步驟 - part 1: convergence
看到釵hmember都有Toshiba的三槍內投影電視,在此與大家分享個人調整心得。
I have a Toshiba TW56F80 56吋、16x9 電視, bought 3 years ago, 美金定價$5000, it's Toshiba's top of the line at that time. But it's not a line-doubled set like their newer generation TW56X81. I have entered its service mode, and successfully fine tuned many parameters to a very satisfactory degree.
[B]警告[/B]:進入 service mode may change so drastically of your current settings, please write down all the current setting values before you proceed. 一切後果請自行負責。
微調步驟與項目如下:
1. Clean the optics/mirror
2. CRT Focus (mechanical and electrical)
3. Geometry adjustment
4. Convergence of 3 CRT
5. White Balance
6. Contrast/Brightness
7. Color/Tint
Today, let me write item 1 and 2 first.
1. Cleaning
My TV was very sharp and good contrast when I first bought it. Over the years it becomes less focused, and not as sharp. Last week, after 搬家, I took down the screen (參考 service manuel) and clean the lens and mirror with 高級的眼鏡絲布, don't use any liquid or windex. Boy! when I cleaned the Green gun, I was shocked to see what a difference! The other two uncleaned ones look like grey, and the cleaned one is shining! Anyway, I carefully cleaned the CRT surface and mirror, then I put back the screen. Without further fine tune, boy, the picture jumped out, 比以前景深更加 畫面更活。Cleaning is a must for a certain period (say 6 month) since the CRTs are facing upward, dust can accumulate, especially in Taiwan as it's damp and more dusty.
2. Focus
There are two focus adjustment: 機械式與electrical的。機械式需轉鬆3 CRT後再調整,特別奉勸省略此步驟,太危險,難度非常高。electrical的較容易。
My TW56F80 has a Focus VR 可變電阻,可調整光學的focus. 卸下前面的木板後,就藏在speaker 旁邊。 First, enter service mode如下:大開電視,press 遙控上的Mute一次, then 按著 Mute 鍵同時按電視上的menu鍵,您可看到電視上有一個小s字母,此時按遙控上的menu, you can see RCUT followed by a number, you are in service mode now.
Once you are in, first take a pen and write down all the parameter you read on the screen before you make any changes. Press CH +/- to change parameter items, Volumn +/- keys can change the value, but don't change any yet, just use CH +/- to go through the items first (30+) and copy down all the values and parameter names.
When you are back to RCUT item, press number 7 to call up a 56 point grid (for convergence), now adjust the Focus VR as follows: (AND don't touch the Screen VR, it changes the white balance)
First, press key '100' to cancel Red, 'RTN' to cancel Blue, now you have only green grid. 前後轉動Green的VR鈕直到最緊的線條出現為止。 press key '100' to add Red back, and '0' to cancel Green. Now do the same to focus Red. Finally, cancel both red and Green, press 'RTN' to call back Blue, now do the Blue. Blue lines are fatter than the other two colors. O.K., now you are done with focus.
在不動其他的parameter下,調整步驟1與2已可讓你的電視對比更佳,影像更嚴謹。假如電視是新買的或對目前的影像很滿意,可能沒有必要調整,假如是一年以上或對目前的影像不滿意,建議可考慮調整看看。
下一次再介紹其他的調整以及弁鄍i怕的design mode。
林宗毅 |
|