忘記密碼
 立即註冊
查看: 1380|回覆: 12

NSH 投影機燈泡加 Kenko FL-W 濾鏡初體驗

  [複製鏈接]

30

主題

397

回帖

0

積分

新手上路

二星級會員

舊站積分
9
舊站發表文章數
424
發表於 2002-2-27 12:18:37 | 顯示全部樓層 |閱讀模式
昨天花 $480 買了 Kenko FL-W 55mm,興沖沖跑回家試裝,靠!竟然合不來,難道投影機製造商和照相機製造商各行其道?真是不可思議。

好吧,辦法是人想出來的。幸好濾鏡口徑小了約 1mm,試過橡皮筋、電氣膠帶都不成功,不知怎的,突然找到一條軟碟機用的排線,厚度正好,塑膠外皮又有可塑性,於是撕下兩芯迷你排線,比好口徑之後焊起來,再用點力氣扣入濾鏡的公牙上,再把凸起的焊錫銼平,竟然就鎖上去了,真是狗屎運。

天色太亮,先回公司再找了一下 Hoya FL-D, FL-W 及 B+W FL-D 的資料,嘿,有趣的事情﹕B+W FL-D 和 Hoya FL-W 其實是相同用途的東東,只是命名讓人丈二金剛,摸不著腦袋。先前看 B+W 型錄,搞不懂為什麼它的 FL-D 是淺紫色,和 Hoya FL-W 顏色一樣,如今總算、、、

以下純屬外行人的淺見,請多多包涵。錯誤之處也請不吝指正,謝謝。

晚上打開投影機和電腦,故意不開擴大機避開聲音干擾,全神貫注在色平衡上。抽取盒裡硬碟甲的<劍魚>畫質銳利,可是室內場景多,螢光燈的綠色偏非常嚴重,不適合作第一次調校用,但戶外場景多、色平衡佳的<貓狗大戰>在硬碟乙上且未放入抽取盒,只好將就先用<劍魚>來作加、不加濾鏡的比較。

先把 ZoomPlayer/Radeon VE Overlay 調為0 IRE加 Gamma = 32 的輸出,NEC VT540K白平衡裡的 RGB Brightness 及 RGB Gamma 全部回到出廠中間值(就說它等於 0 – 10 中間的 5 吧)。暫停畫面是<劍魚>裡黑人探長正在偵訊芬蘭駭客,作胸部以上特寫,螢光燈恰好被他的頭遮掉一半。未加濾鏡時,由於場景螢光燈的綠光已經很強(攝影師未加 FL-W 一類的濾鏡該打屁股?),再加上投影機 UHP/NSH 燈泡的偏藍偏綠天缺,等於是禍上加禍,光源和探長臉部的反差非常強(這是事後回想才悟出來的,沒看過濾鏡效果之前,並未察覺這個問題,祇粗淺感覺<劍魚>畫質銳利,但室內場景多,螢光燈的綠色偏非常嚴重)。

用手持濾鏡加上去來回比較,可以看到加了濾鏡後,這樣的反差頓時緩和下來,觀看時的感受及立體感的差異可說不小,而且那時還未動手調 RGB Gamma,就己經被較好的色平衡後的畫面衝擊了一下下。

鎖上濾鏡,接著換上<貓狗大戰>,慢慢地、輪流看紅、綠、藍的表現然後調整 R, G, B Gamma,發現紅仍然不夠,藍、綠仍然太多,但儘量都繞著中間值 5 來調,已經比未加濾鏡好很多。得到初步值之後,接著再看了幾部電影觀察及微調,發現 R Gamma = 6.2, G Gamma = 4.2, B Gamma = 3.8 時,三色平衡是最理想的。此時再回頭看<劍魚>,雖然片源的綠色偏仍在,但已經大大可以接受了,黑人探長的臉部色澤非常逼真,油亮的額頭還反射著光,立體感進步好多﹔看<貓狗大戰>則比以前更加享受,人臉的膚色表現可圈可點,花卉、綠葉的色澤相當正確、自然。古典傢俱的紅木色澤、紅色地毯及紅色厚窗簾布都有可取之處,讓我不知不覺一直玩到凌晨 12:30 才依依不捨關機睡覺。

AVS Forum 有人提到 Marantz 投影機(未記型號)已附贈濾鏡,可能就是針對燈泡三色輸出不均的天缺所特別訂製的。在你我的寶貝 DLP/LCD/DILA 投影機還沒有量身訂作的燈泡/內外濾鏡組合出現之前,先用攝影濾鏡大幅躍進實在是俗又大碗的偏方,關心畫質的各位一定要試試。

接著想做 CC30/20R 和 Hoya FL-D 實驗,但國內取得不易。金屬兄的 SINAR CC40R 是膠片還是玻璃片,可否向大伙介紹一下。

84

主題

262

回帖

50

積分

新手上路

重金屬毒患

舊站積分
15
舊站發表文章數
257
發表於 2002-2-27 12:38:19 | 顯示全部樓層

Re: NSH 投影機燈泡加 Kenko FL-W 濾鏡初體驗

彭兄
目前國內能買到的CCR濾鏡,都是塑膠材質
所以透光度會比玻璃差些,所以才想買B+W CCR20回來試
不過好貴[xx(] ,故若您想團購此鏡頭,請記得算我一份
謝謝囉!
SOPHIE MARCEAU NICOLE KIDMAN MEG RYAN CATHERINE ZETA-JONES

21

主題

412

回帖

0

積分

新手上路

永久榮譽會員MYAV全體網兄致敬

舊站積分
4
舊站發表文章數
441
發表於 2002-2-27 14:10:22 | 顯示全部樓層
彭兄 ,

The Hoya FLD cut around 45% blue, 45% green and 25% red in average.
The Hoya FLW cut around 40% blue, 65% green and 40% red in average.
CC30R cut around 40% blue, 40% green and 10% red in average.

If you buy glass FLD and FLW filter, you should choose multi-coated one.  There is much less reflection comparing normal single coating.  For CCR filter, there is one called Optiflex which is only 0.3mm thick.  I believe the light transmission rate should be high.

P.S.  Regarding the overlay control at Zoomplayer, the midpoint of brightness is not equal to the midpoint of that at ATI driver control.  I found that the 0 IRE setting of Zoomplayer is so bright that make the picture wash out.  7xx of Zoomplayer brightness is equal to the midpoint of ATI brightness.

30

主題

397

回帖

0

積分

新手上路

二星級會員

舊站積分
9
舊站發表文章數
424
 樓主| 發表於 2002-2-27 14:28:12 | 顯示全部樓層
CKL,

I had read your posts on AVS forum and impressed. The filter experiment is actually inspired by Mr. Wiggles, Guy Kuo and you on the same thread.

How do you get to know all these transmittances each filter provides? Solute... and mind telling me if it is accessible through internet and web URLs? These figures are a bit different than those from Guy Kuo and I am urged to verify. Thank you.

It's pathetic that only Kenko FL-W is available in Taiwan. I'd like to have glass CC30R and Hoya MC FL-D but still am stuggling. Is it easy to get these in HK? Any tips for guys in Taiwan?

BTW, how is your DIY DVD-Rom going? Hooked to HTPC still?

Happy AV new year.

30

主題

397

回帖

0

積分

新手上路

二星級會員

舊站積分
9
舊站發表文章數
424
 樓主| 發表於 2002-2-27 14:40:15 | 顯示全部樓層
Regarding ZoomPlayer 0 IRE issue, if memory serves, was an ATI 7199/3286(?) driver problem. I had it once on my triple boot 98se. I hardly use it no more.

ATI 3276 under Win2k sp2 does not suffer this problem and  mostly, especially after the Kenko FL-W I believe, 0 IRE under ZoomPlayer serves my eyes well with VT540K on self painted gray wall.

Regards.

21

主題

412

回帖

0

積分

新手上路

永久榮譽會員MYAV全體網兄致敬

舊站積分
4
舊站發表文章數
441
發表於 2002-2-27 15:32:04 | 顯示全部樓層
The figure is the rough average value.  The absorption rate varies against the spectrum.  For the exact spectrum response of FLD, FLW and CC filters, go to:

http://www.avsforum.com/avs-vb/showthread.php?threadid=116406&perpage=20&highlight=Hoya%2081B&pagenumber=3

I can buy Hoya single coated FLD and FLW in Hong Kong but the HK distributor doesn't import the HMC (multi-coated) version.  I have Hoya HMC UV filter which is used for the hushbox.  I've compared it with normal single coated one.  The reflection is much less.  Hoya HMC is very good considering the price.  It is also not easy to find CC filters in HK.  I'm going to order Hoya HMC and CCR filters from the internet.  

I use Zoomplayer in WinME and XP.  I tried several beta ATI drivers with overlay control.  The same problem occurred.  I don't know the situation of Win2000.  Anyway, I prefer using the ATI overlay control to that in Zoomplayer, although Zoomplayer is more convenient.

I'm still looking for a smaller case to install DVDROM.  I don't want to use the big case for a whole PC.  But for the best performance, it is better to modify the DVD player with SDI out and connect it to SDI card in HTPC via BNC cable.

30

主題

397

回帖

0

積分

新手上路

二星級會員

舊站積分
9
舊站發表文章數
424
 樓主| 發表於 2002-2-27 15:49:19 | 顯示全部樓層
CKL,

If you had qualified any internet supplier for these filters, please share with us.

What's you and Li On's conclusion in selecting filters for these UHP/NSH lamps? Have you found the one and only Mr. right for our lovely Ms. PJ?

21

主題

412

回帖

0

積分

新手上路

永久榮譽會員MYAV全體網兄致敬

舊站積分
4
舊站發表文章數
441
發表於 2002-2-27 16:50:45 | 顯示全部樓層
The output of RGB is not the same even using the same lamp because the light will pass the LCD/DMD panels and then the lens. It's hard to say which filter is the best for UHP/NSH/NSM lamps.

The manufacturers should have the spectrum reponse of the lamp they used.  They can install a filter in front of the lamp in the light chamber of the projector.  The filter is tailor-made to ensure the light source to be 6500k and having the minimum brightness drop.  If the manufacturers can do that, it will be the best.  If the filter is installed in front of the lens, the reflected light will go back to the LCD/DMD panel which may degrade the picture quality.   If the filter is  installed in front of the lamp, the reflected light is less hurtfull.

15

主題

336

回帖

0

積分

新手上路

二星級會員

舊站積分
3
舊站發表文章數
343
發表於 2002-2-27 21:25:44 | 顯示全部樓層
我用過了 Kenko 的 FL-W 不過感覺不太好
原因是顏色好多了可是透明郤是差多了
所以氣急敗壞之下只好到
http://www01.bhphotovideo.com/de ... 0___SID=EC7D6070880
買了  Hoya  FL-D Fluorescent (HMC) Multi-Coated Glass Filter for Dayligh  再試試看透明會不會降太多
還有該網站接受 B+W CC20R 的預定約 2-6 週不過一片 102 元 [!]
所以還是選了便宜 Hoya http://www01.bhphotovideo.com/de ... 0___SID=EC81CDC4320
CP 比較高是 HMC 應該不會太差 AVS forum 也提說 B+W 太貴了

bty 我買了 4 片扣掉自已用與朋友的,要的話分攤一下運費

30

主題

397

回帖

0

積分

新手上路

二星級會員

舊站積分
9
舊站發表文章數
424
 樓主| 發表於 2002-2-28 15:22:36 | 顯示全部樓層
Hoya FL-D HMC 尺寸是 55mm 嗎?若是,我要一片。
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-23 05:33 , Processed in 0.296215 second(s), 42 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表