忘記密碼
 立即註冊
查看: 2124|回覆: 4

[求助]MEEDIOS播放高清片如何設定S/PDIF(光纖)輸出至舊規擴大機

[複製鏈接]

18

主題

59

回帖

0

積分

新手上路

初級會員

舊站積分
0
舊站發表文章數
49
 樓主| 發表於 2009-3-24 23:44:30 | 顯示全部樓層

[求助]MEEDIOS播放高清片如何設定S/PDIF(光纖)輸出至舊規擴大機

小弟最近組了一台HTPC,音效卡是裝上ASUS XONAR HDAV1.3,最主要目的就是當高清撥放機來使用

不過擴大機是多年前舊規的機子(YAMAHA DSP-A2),目前是用光纖線做音訊的輸出(入)

用bd光碟機撥放藍光片的時候,音效卡設為PCM輸出,播放軟體(POWERDVD 8)的音訊設為S/PDIF輸出

擴大機可正常輸出DOLBY DIGITAL 5.1或DTS 5.1聲道(小弟有的片子當中,唯一不行的是"變形金剛"選單畫面有聲音,進入電影後就沒聲音了)

但用MEEDIOS播放下載的高清片,擴大機就一點聲音都沒有,連DOLBY DIGITAL或DTS的燈沒亮,表示HTPC根本就沒輸出音訊給擴大機

請問達人大大們,MEEDIOS要如何設定才能正確輸出音訊至小弟的舊規擴大機呢?感謝

17

主題

566

回帖

0

積分

新手上路

 

舊站積分
295
舊站發表文章數
562
發表於 2009-3-25 00:29:18 | 顯示全部樓層
請按您系統選對應的數位輸出


進kmp後按f2 進設定


進音訊處理 如圖選到 asus 數位輸出


到下圖 外部音訊解碼器項目諳箭頭處


檢查紅圈內設定如圖


關閉後重開kmp 即可

18

主題

59

回帖

0

積分

新手上路

初級會員

舊站積分
0
舊站發表文章數
49
 樓主| 發表於 2009-3-25 11:49:24 | 顯示全部樓層
感恩大大把每個步驟還連圖帶文的仔細說明,就感心ㄟ[!8]

只是照著大大的步驟去設定,試了好幾次,最終還是殘念,擴大機不出聲就是不出聲

不知是哪個環節出問題(好想換新規的擴大機啊),只好再try try看,再次感謝大大的指導

5

主題

20

回帖

0

積分

新手上路

初級會員

舊站積分
0
舊站發表文章數
20
發表於 2009-3-25 16:03:50 | 顯示全部樓層
原發表者是 jackie888
[B]感恩大大把每個步驟還連圖帶文的仔細說明,就感心ㄟ[!8]

只是照著大大的步驟去設定,試了好幾次,最終還是殘念,擴大機不出聲就是不出聲

不知是哪個環節出問題(好想換新規的擴大機啊),只好再try try看,再次感謝大大的指導 [/B]


內部音訊解碼器小弟印象中

要把DTS取消打勾不能用預設的

轉譯器有改試看看POWER DVD的嗎

如果視訊輸出是用HDMI端子

有時候他會誤認聲音要從HDMI輸出喔

這邊也要改

17

主題

566

回帖

0

積分

新手上路

 

舊站積分
295
舊站發表文章數
562
發表於 2009-3-26 00:52:03 | 顯示全部樓層
http://vip.asus.com/forum/view.aspx?id=20080423032545000&board_id=21&model=Xonar+D2X&page=1&SLanguage=en-us


參考官方說法試試

I was looking through the forum due to my own problems (the popping/beeping noises due to the DTS/DD signal being incorrectly handled through the SPDIF) when I noticed alot of people wonder how come when they set the "Digital Output" device as default, there isn't any DTS/DD signal.

To correctly set it, you need to set your "Speakers" as the default device in the "Sound" control panel (which can be found in Control Panel, or right click your Volume icon in the tray bar and select "lay Back Devices").

Then you open the "Xonar Audio Center" tray icon by clicking it, and setting the input to any of the multi-channel input (depending on how many sound channels is produced from what you are doing [gaming, movies, etc.]).  And set the SPDIF OUT on to DTS or DD.

If you want to know why you set Speakers to default to get sound out your Digital Output Device (SPDIF), or why you need to select how many channels the source has instead of the software doing it for you, continue reading.

Why do I need to set Speakers as default output instead of Digital Output Device?

The explanation:  Although the ASUS XONAR runs on a proprietary ASUS sound processor, this SPU was actually co-developed with CMEDIA (and seems to bare a close resemblance to the CMEDIA CMI8788), as well the software is based on XEAR3D (as you can see when you click the "About" button in the XONAR Tray Icon).

And the technique to convert the regular analog output to digital output was designed under the same architecture to solve a big problem: Windows SUCK.

Windows only encodes/understands 2 channel output through the SPDIF, so when Windows is in control, sound can only be in stereo.  What Windows can do is to give an application exclusive control over the sound card and allow SPDIF passthrough for DTS/DD sound.  But when you give exclusive control of the sound card and allow SPIDF passthrough, you no longer have control over volume, post-processing, and etc. because the sound is directly passed through from the device to the sound card.  And at this time, only the application in control can produce sound, so there is no sound from Windows, MSN, or anything else for that matter, since only the device has EXCLUSIVE CONTROL over the SOUND DEVICE.

i.e. When playing DVD with DD/DTS using SPDIF passthrough for 5.1+ channels, and your friend messages you on MSN, you don't hear it, because the DVD has exclusive control of your sound card.  Also, you won't be able to change the volume.

So how does the sound card output SPDIF above 2 channels?

The solution from CMEDIA was to first output as ANALOG PCM, then convert through software/hardware to the SPDIF.  This way all sound is output as 5.1+ analog channels (which Windows CAN do), and then convert it to SPDIF.

i.e. Sound Source -> 6 channel Analog Output -> Convert to SPDIF -> SPDIF Out

But in order to do this, as I said before, the sound needs to be output as 6 channel Analog Output first.  If you set the "Digital Output Device" as the default device, this is what Windows sees:

Sound Source -> 2 Channel SPDIF Out

So it can only produce 2 channels.

In order to convert multi-channel audio to SPDIF, you need to set Analog Output Device aka "Speakers" as the default device.  Then you need to configure it to 5.1 or 7.1 channel (whatever you have setup) under the "Sound" control panel.

After doing so, what Windows sees is that you have 5.1/7.1 channel output to Analog, and starts sending sounds to those channels.

Windows:
Sound Source -> 6 Channel Speaker Out

But what happens is that the software catches the 6 Channel Speaker Out, converts it into DTS/DD, then outputs the SPDIF.

XONAR Software/Hardware:
Sound Source -> 6 Channel Speaker Out -> convert to DTS/DD -> output SPDIF

---

Why do I have to choose how many channels is my source?

The explanation:  As I said before, the sound is output to the Analog Output channels, then caught by software/hardware and converted to DTS/DD and output to the SPDIF, right?

So imagine windows plays something and outputs to the 6 channels:

1 sound
2 sound
3
4
5
6

and the software/hardware captures the 6 channels.  How many channels are there?  Are there 6 channels, or 2 channels?  It could be there are 6 channels, but only first 2 channels has sound.  Or it could also be the input only has 2 chanel sound?

Or what if you play music (2 channel) and a video (6 channel) [let's say news, cause sometimes people watch news and listen to music at the same time].

The software can't tell how many channels there are unless you tell it.

What is the benefit to setting to 2 channel?

You can upmix to multichannel (DTS:NEO, DD Pro Logic II, etc.).  Upmixing means converting 2 channel to multichannel sound.

However, if your source is 6 channel, and you try to upmix it, it screws up the sound and is no longer accurate because the software is looking at only the first 2 channels and ignoring the other 4.  So you need to set it to 6 channel.  (That's why DSP such as DTS:NEO, DD Pro Logic II, etc. are not available when set to 6 or 8 channel sound outputs).
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-20 21:05 , Processed in 0.096159 second(s), 31 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表