忘記密碼
 立即註冊
查看: 3166|回覆: 13

是調整唱頭角度而不是調整唱臂支點高度(VTA)

[複製鏈接]

381

主題

6296

回帖

0

積分

新手上路

五星級會員

舊站積分
4727
舊站發表文章數
6119
發表於 2009-8-21 10:47:58 | 顯示全部樓層 |閱讀模式
這是我畫的唱針在各種情況下移動的角度


我在唱頭前墊一片厚紙片調整唱針角度


我個人覺得調整唱臂高度應該是錯誤的行為
由圖(一)可以知道
當唱針與唱臂旋轉支點成水平才是合理的移動方式
水平支點與垂直支點高度不同的唱臂最遭糕
***(但我不知道目前大部份的唱臂情況是如何?)
唱針移動方向應該與唱盤成垂直狀態
否則若有角度偏差時
唱針截取的音樂訊號會不正確.....(可能影響波形)
因此我提出..........要調整唱頭角度而不是調整唱臂支點高度
唱針(盤面)與支點在同一水平面上
才是正確的調整方式......雖然很麻煩...

以上是個人實驗與經驗談
請前輩用力批評指正.........[|)]

59

主題

4420

回帖

0

積分

新手上路

四星級會員

舊站積分
489
舊站發表文章數
2513
發表於 2009-8-21 10:55:09 | 顯示全部樓層
jcc104 老師上課您都沒在看?  [:O]

381

主題

6296

回帖

0

積分

新手上路

五星級會員

舊站積分
4727
舊站發表文章數
6119
 樓主| 發表於 2009-8-21 11:06:55 | 顯示全部樓層
原發表者是 jfli0325
[B]jcc104 老師上課您都沒在看?  [:O] [/B]



請jfli0325兄明示..............[]

59

主題

4420

回帖

0

積分

新手上路

四星級會員

舊站積分
489
舊站發表文章數
2513
發表於 2009-8-21 11:21:02 | 顯示全部樓層
原發表者是 xtype
[B]


請jfli0325兄明示..............[] [/B]


落落長, 而且老仙的調整挖也挖不完[]

http://www.myav.com.tw/bbs/showt ... amp;pagenumber=1111

調整是一整套, 直接請教 jcc104老仙比較快[]

167

主題

8萬

回帖

0

積分

新手上路

五星級會員

舊站積分
32767
舊站發表文章數
11966
發表於 2009-8-21 12:15:40 | 顯示全部樓層

Re: 是調整唱頭角度而不是調整唱臂支點高度(VTA)

原發表者是 xtype
[B]
我在唱頭前墊一片厚紙片調整唱針角度
[/B]


重點是針尖(tip)的角度(也就是針桿的角度)

而不是唱臂,甚至是唱頭的角度

像你這樣墊前面,VTA 變得更大,

就必須加大針壓,才能使針尖處在正確的角度

要使用低針壓(降低針壓),必須墊後面,使 VTA 降低

你現在是反其道而行

另外,墊紙片,不是個好主意

剛性不好,會吃掉細節

381

主題

6296

回帖

0

積分

新手上路

五星級會員

舊站積分
4727
舊站發表文章數
6119
 樓主| 發表於 2009-8-21 17:06:59 | 顯示全部樓層

Re: Re: 是調整唱頭角度而不是調整唱臂支點高度(VTA)

原發表者是 wecare
[B]

重點是針尖(tip)的角度(也就是針桿的角度)

而不是唱臂,甚至是唱頭的角度

像你這樣墊前面,VTA 變得更大,

就必須加大針壓,才能使針尖處在正確的角度

要使用低針壓(降低針壓),必須墊後面,使 VTA 降低

你現在是反其道而行

另外,墊紙片,不是個好主意

剛性不好,會吃掉細節 [/B]


重點.....旋轉中心與唱針水平位子置要一樣高


加大唱頭角度(加墊片)是因為配合降低唱臂高度
達到旋轉中心與唱針水平位子置一樣高度
至於正確的針尖角度並不需要特別加高針壓
這些我都考慮到了

這樣的調整讓我得到很好的聽感
就算播放魷魚片時音質也相當不錯
比旋轉中心與唱針水平位子置不一樣高時的音質表現相對穩定多了

墊紙墊片時我並沒有覺得細節被吃掉的感覺
不過我會把墊片換成鋼性強一點的材質....(鋁片.檜木...等)
我想不是所有的唱臂都需要加墊片
那必需視唱臂被調整多少而定
如果只調整幾mm應該是不用加墊片的
像我這個唱臂足足調低了22mm
才達到旋轉中心與唱針水平位子置達到一樣高度

我要訴求的理論是.....
不要改變唱臂支點的高度
而是改變唱頭的角度才對
但先決條件是....(旋轉中心與唱針水平位置必需一樣高)
這種調整下的優點
在播放不平整的唱片時感覺最清楚[]

67

主題

1萬

回帖

0

積分

新手上路

Witch Fly on the Tonearm

舊站積分
7022
舊站發表文章數
12209
發表於 2009-8-21 17:41:34 | 顯示全部樓層
可以參考Neutral Balance的想法

http://www.graham-engineering.com/

[;)]
站在巨人的肩膀上 我們看得更遠

381

主題

6296

回帖

0

積分

新手上路

五星級會員

舊站積分
4727
舊站發表文章數
6119
 樓主| 發表於 2009-8-21 18:13:23 | 顯示全部樓層
原發表者是 jcc104
[B]可以參考Neutral Balance的想法

http://www.graham-engineering.com/

[;)] [/B]


又是英文.........救命啊!
我用語言翻譯器......有看沒有懂
看的懂的網兄可否說一下重點......拜託!

The original Phantom is the result of over two years of research into design theory, materials analysis, and extensive testing. This involved not only testing of the individual design components as they were being evaluated, but also comparing the several prototype models against our own Model 2.2 and the available competition.

In designing our newest tonearm, the Phantom II, we knew it had to be far superior not only to other fine tonearms available, but also to our own Model 2.2. If it weren't, there would be no reason to continue the project.

The final result, the B44 Phantom II ,  has exceeded even our highest expectations, surpassing even the highly-rated Phantom I..   

And this is even more true when compared to other tonearms; the Phantom simply is in another, far higher, plane of performance.

Compared to the orignal Phantom, the new Series II  has a similar outward appearance, but has important internal differences.   These include a refined Magneglide (tm) stablizer, new internal wiring for even better detail and improved freedom from any mechanical resistance, an upgraded pivot design for even greater dynamics, and a new titanium armwand.  Together, these improvements yield greater performance in the areas of dynamics and sheer musicality, while retaining the features the earlier Phantom was noted for.  

The reasons for these and other significant improvements are many, and are covered in  three patents, with other applications pending.  

The armtube itself, easily removable and using our patented alignment system, offers the safety, convenience and accuracy of off-turntable cartridge installation and alignment, as well as allowing quick interchange of multiple pre-mounted cartridges. It is significantly improved from the earlier armwands, and attaches to a nearly half-inch wide stainless-steel post-and-connector that supports the armwand under tension, resulting in virtually a one-piece armtube/pivot assembly with high damping.

Secondly, we've addressed the all-important (and often ignored) area of dynamic balance. Tonearms should have as little inertia as possible; yet, too often, as a result of the correct placement mass distribution being overlooked, they contribute excessive resisting forces in opposition to the requirements of the phono cartridge as it attempts to follow the ups and downs of a typical record. The Phantom, in spite of its robust appearance, has been designed with a very low moment of interia, so that the majority of phono cartridges can be used with ease and maximum performance.

-- At this point, a brief description of Balance Theory may be helpful: There are basically three types of static balance systems, Neutral, Stable, and Unstable. Stable balance, normally seen in laboratory scales, occurs when the CG (center of gravity) of the moving system is placed BELOW the pivot point. When this type of system is displaced from its preferred rest position, it will generate an immediate and opposing force which tries to return to that same position.

Unstable balance, when the pivot point is below the pivot point, is entirely useless for tonearm design, and will exhibit serious  problems, including reduced tracking force as the arm is raised.

The third, and most desirable system for tonearms, is Neutral Balance. With this system, the pivot point and the Center of Gravity of the moving system are in the same plane. When the arm is raised or lowered, there is no opposing force trying to return the arm to a rest position; the pivoting system doesn't really know or care if the stylus is at the record surface level or a half-inch above or below it; as a result, there is no opposing force to the arm as it is traversing record deflection during play. The only downward tracking force is that of the adjustable counterweight, which remains a constant. --

Previously, all true unipivots - that is, those with a single contact point for the bearing and NO secondary stablizing surfaces, bearings, etc. - required the use of side weights or a significantly lowered counterweight in order to provide stability. And generally speaking, those arms with a secondary stabilizer point require a lowered center of gravity in order to provide constant contact with the stabilizer guide bearing.

The drawback to both these conditions is that this design becomes a Stable Balance system, which will cause a tonearm to have a preferred rest position and always tries to return to this point.   ANY time the tonearm is raised, as in tracking warped records, it results an immediate and equally opposing force that tries to push the arm back to its rest position.  The higher the warp, the more counter-force is applied.

This unalterable Law of Physics will work against the cantilever, deflecting it during warps and causing the magnetic system inside the cartaridge to be displaced. This, in turn, will certainly affect the reproduced sound, with diminished performance in all areas, including soundstage compression, loss of detail and dimensionality, not to mention record wear. (This is why most tonearms must have their tracking force measured at the record surface level; any height change during the measurement will cause an incorrect reading).

A tonearm with Stable Balance can be identified by measuring the tracking force at the record surface level and again at a raised position above the record. If the tracking force INCREASES at the higher position, the arm has Stable Balance. Our own previous designs - the best we could make at that time - also had this limitation due to the use of side weights to provide lateral stability.

Other unipivots with low-slung counterweights will all exhibit this force; the lower the weight, the more counter-force is applied. Although this technique is often promoted as a "high-stability" design, it does so at the expense of consistent tracking force and linear cartridge performance. . It actually results in varying tracking forces during play when traversing even small warps, accompanied by non-linear cartidge operation, and increased record wear.

Once Neutral Balance is chosen for use in a unipivot tonearm, one must remember that both the vertical and lateral planes will be affected the same way; without proper lateral stability, such a design would not have consistenent, proper vertical alignment, and the pivot would tend to flop over to one side or another (usually in the direction of the weighted cartridge offset angle mounting). Obviously this condition must be avoided.  

The answer to this lies at the very heart of the Phantom's design and its unique ability to retrieve groove information unprecended in our experience. The key is a magnetic stabilization system which  and which we have called "Magneglide" (TM). With this unique, patented system, all lateral stability, and a portion of the damping, is provided by powerful neodymium ("rare-earth") magnets, placed in a horizontal line from the pivot point of the tonearm.

Working as an adjustable system, Magneglide (TM) provides the following five benefits: lateral stability, azimuth adjustability, damping assist, true vertical pivoting of the stylus tip with no rotation as the arm is raised, and easily adjusted anti-skate compensation.

381

主題

6296

回帖

0

積分

新手上路

五星級會員

舊站積分
4727
舊站發表文章數
6119
 樓主| 發表於 2009-8-21 20:11:23 | 顯示全部樓層
原來的幻影,是由於過去兩年的研究設計理論,材料分析和廣泛的測試。這不僅涉及測試的個人設計的組成部分,他們正在評估,但也比較幾種原型模型對我們自己的模型2.2和現有的競爭。

在設計我們的最新唱臂,幻影二,我們知道它必須不僅遠遠優於其他罰款tonearms提供,而且也對我們自己的模型2.2 。如果不是,那就沒有理由繼續開展這一項目。

最後的結果, B44幻影二,甚至超出了我們的最高期望,甚至超越了高度評價幻影一。

這是更真實相對於其他tonearms ;幻影僅僅是另一種,遠遠高於,飛機的性能。

比起orignal幻影,新的系列二也有類似的外表,但有重要的內部分歧。這些措施包括完善Magneglide (商標)穩定劑,新的內部佈線更詳細和完善免於任何機械性,升級樞軸設計更大的動力,以及一個新的鈦armwand 。總之,這些收益率更高的性能改進方面的動態和純粹的音樂,同時保留了功能早先指出的幻影。

這些原因和其他許多重大改進,並涉及三項專利,與其他申請待審。

該armtube本身,很容易移動,並使用我們的專利定位系統,提供安全,便利性和準確性外轉台墨盒的安裝和校準,並允許快速交換多個預先安裝墨盒。這是顯著改善從早先armwands ,並重視近半英吋寬的不銹鋼樁連接器,支持armwand緊張局勢下,導致實際上是一個單件armtube /樞軸大會高阻尼。

其次,我們已經處理了所有重要的(往往忽視)面積動態平衡。 Tonearms應該少慣性的可能性;然而,往往由於質量分佈正確位置被忽視,它們有助於抵抗力量過度反對派的要求,唱機墨盒,因為它企圖按照起伏一個典型的記錄。幽靈的,儘管它強大的外觀,設計了一個非常低的時刻interia ,所以,大多數唱機墨盒可用於緩解和最高性能。

-在這一點上,簡要介紹了平衡理論可能會有所幫助:基本上有三種類型的靜態平衡系統,中性,穩定和不穩定。穩定的平衡,通常認為在實驗室規模,就會發生在CG (重心)的移動系統是放在下面的支點。當這種類型的系統是其首選流離失所其他位置,它會產生直接和反對武力試圖返回同一立場。

不穩定的平衡,當支點低於支點,是完全無用的唱臂設計,將展出的嚴重問題,包括減少跟蹤武力作為ARM的提高。

第三,也是最可取的制度tonearms ,是中性平衡。有了這個系統,支點和重心移動系統是在同一平面。當ARM是提升或下降,也沒有反對武力試圖返回手臂到其他位置;樞軸系統並不知道或照顧,如果是手寫的記錄表面一級或半英吋,高於或低於它的結果,沒有任何反對力量的手臂,因為它是在穿越記錄偏轉發揮。唯一下降的跟蹤力量是可調抗衡,這仍然是一個常數。 -

此前,所有真正unipivots -也就是說,那些有一個單一的聯絡點,軸承和無二次穩定表面,軸承等-需要使用方重或大幅降低抗衡,以提供穩定。一般而言,這些武器與一個次要穩定點要求降低重心,以提供不斷的接觸與穩定導軸承。

的缺點,以這兩個條件是,這種設計成為一個穩定的平衡系統,該系統將導致唱臂有一個首選其餘的立場和一貫試圖返回了這一點。任何時候唱臂提高,如在扭曲跟蹤記錄,但結果同樣立即和反對的力量,試圖把手臂回到休息的位置。越高,變形,更反力的應用。

這種不可改變的規律的物理學會工作的懸臂,轉移過程中造成扭曲和磁系統內cartaridge流離失所。反過來,這必將影響轉載穩健,降低性能的所有領域,包括聲音壓縮,損失的細節和立體感,更不要提記錄磨損。 (這就是為什麼大多數tonearms必須有自己的跟蹤測量部隊的記錄表面水平;任何高度變化的測量會導致不正確的閱讀) 。

阿唱臂與穩定的平衡可以通過測量跟蹤武力的記錄水平和表面上再次提出上述立場的記錄。如果追蹤武力的可能性較高的地位, ARM公司穩定的平衡。我們自己以前的設計-最好的,我們會在那個時候-也有這個限制,由於使用方重量提供橫向穩定性。

其他unipivots低投擲重物將所有展品這支部隊;較低的重量,更反力的應用。雖然這種技術往往是促進作為一個「高穩定」的設計,它這樣做犧牲了一致跟蹤武力和線性墨盒性能。 。它在不同的實際結果跟蹤部隊在穿越時發揮甚至小索的陪同下,非線性cartidge操作,並增加記錄磨損。

一旦中性平衡的選擇用於unipivot唱臂,人們必須記住,在縱向和橫向的飛機將受到同樣的方式;沒有適當的橫向穩定性,這樣的設計也不會consistenent ,適當的垂直排列,並樞軸會往往失敗給一方或另一方(通常的方向偏移角加權墨盒安裝) 。顯然,這種情況必須避免。

答案在於核心的幻影的設計和其獨特的能力來檢索信息unprecended槽在我們的經驗。關鍵是磁穩定系統,和我們所謂的「 Magneglide 」 (商標) 。這一獨特的,專利制度下,所有的橫向穩定,部分阻尼,提供了強大的釹( 「稀土」 )磁鐵,放置在一個水平線的支點的唱臂。

作為一個可調系統, Magneglide (商標)提供了以下五個好處:橫向穩定,方位可調,阻尼協助,真正垂直樞軸的鐵筆提示沒有輪換作為ARM的提高,很容易調整反滑冰賠償。

646

主題

7251

回帖

0

積分

新手上路

五星級會員

舊站積分
1789
舊站發表文章數
4663
發表於 2009-8-21 20:25:25 | 顯示全部樓層

Re: Re: 是調整唱頭角度而不是調整唱臂支點高度(VTA)

原發表者是 wecare
[B]

重點是針尖(tip)的角度(也就是針桿的角度)

而不是唱臂,甚至是唱頭的角度

[/B]


是滴....正解..... []


調整vta是為了針尖與唱片的垂直度...
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-19 00:49 , Processed in 0.310711 second(s), 43 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表