忘記密碼
 立即註冊
樓主: chucky7

美國網路直售喇叭和超低音的經營生態和使用觀點

[複製鏈接]

249

主題

3萬

回帖

220

積分

新手上路

上將

舊站積分
11603
舊站發表文章數
26283
發表於 2017-9-16 14:16:15 | 顯示全部樓層
原發表者是 chucky7
[B]From http://data-bass.com/know-how

[B]Data-bass 上對 [B]Group Delay[/B] 的解說:[/B]

A group delay graph is derived from previous measurements. This measurement indicates how much delay or storage of energy versus frequency is taking place in a system. Larger values in MS indicate more latency or energy delay.Ideally there would be zero group delay indicating an incredibly well damped system. In reality there is always some. Generally it is held that as long as the delay is below 1.5 cycles it is inaudible and most who claim to hear differences in delay between speakers would say that anything less than 1 cycle of delay is nothing to worry about. Additionally the deeper in frequency, the longer the wavelength and less sensitive our ears are to it the less audible a long group delay will be. Generally anything below 25-30Hz is not regarded as of much concern unless really bad. For example 40ms of delay at 25Hz is probably not a big deal and not very audible but 40ms of delay at 80Hz is going to be much more audible and of concern. Typically sealed, IB and other lower order systems offer the least amount of delay...Bass reflex systems typically have increased delay near the resonator tuning. Even higher order systems like horns and Bandpass enclosures can have more group delay and more complex delay plots. Additionally equalization and other signal processing, such as high pass filters and boost or parametric signal shaping can increase the group delay. [B]Usually this measurements indicates nothing of concern unless the group delay is exceeding 1.5 cycles above 25Hz. [/COLOR][/B]

From http://data-bass.com/data?page=system&id=117&mset=129

[B]Data-bass 上對 JTR Captivator 1400 Group Delay 的評語[/B]

Group delay and decay of energy is [B]well controlled[/COLOR][/B] until down near 20Hz where the group delay just reaches 1 cycle. Near the vent tuning and high pass filter the delay does grow to around 1.5 cycles but [B]at such a low frequency this is of no audible consequence.[/COLOR][/B] [/B]

原發表者是 chucky7
[B]

皇帝位的 Group Delay:
[/B]


chucky7兄

照他這段講

\\Usually this measurements indicates nothing of concern unless the group delay is exceeding 1.5 cycles above 25Hz.

你的43hz 跟 50hz約近100ms就有超過1.5個週期的GD,你想會是甚麼造成的....外測沒有就剩空間跟機器設備了...你的看法?。
[url=http://www.myav.com.tw/market/showthread.php?s=&threadid=5991]進口超值--色差、同軸數位、S線[/url] [url=http://www.myav.com.tw/market/showthread.php?s=&threadid=127614]綜合商品區[/url] [url=http://www.myav.com.tw/market/showthread.php?s=&threadid=20459395]In-akustik 德國敏力線[/url]

0

主題

110

回帖

0

積分

新手上路

二星級會員

舊站積分
42
舊站發表文章數
110
發表於 2017-9-16 14:19:38 | 顯示全部樓層
原發表者是 L&J
[B]
最後就剩下,超低音有沒有所謂的音色
或是音色是不是不該形容在超低音所聽到的不同. [/B]


我也很好奇那個音質排名是怎麼測出來的?
不是有人說超低音音質音色之類的不明顯,
怎麼老外就可以排名?

34

主題

1311

回帖

0

積分

新手上路

Da Man

舊站積分
1718
舊站發表文章數
1326
 樓主| 發表於 2017-9-16 14:56:41 | 顯示全部樓層
原發表者是 ups
[B]

chucky7兄

照他這段講

\\Usually this measurements indicates nothing of concern unless the group delay is exceeding 1.5 cycles above 25Hz.

你的43hz 跟 50hz約近100ms就有超過1.5個週期的GD,你想會是甚麼造成的....外測沒有就剩空間跟機器設備了...你的看法?。 [/B]


跟該分貝的頻率響應一起看...


我在 40 ~50 Hz 中間有 room mode 波鋒 peak... 這是環境造成的 [xx(] ... 不過, 我還嫌我的系統無法帶給我搥胸口的感受, 當然捨不得去收服它呀... [] [}]

Data-bass 的解說有提到這是 GD 是 system damping 系統減震的問題. 但我這 43Hz 和 50Hz 是環境... 這... 視聽環境可以做減震嗎? 難道要叫我做音場處理嗎? [:I]

249

主題

3萬

回帖

220

積分

新手上路

上將

舊站積分
11603
舊站發表文章數
26283
發表於 2017-9-16 15:12:24 | 顯示全部樓層
原發表者是 chucky7
[B]

跟該分貝的頻率響應一起看...


我在 40 ~50 Hz 中間有 room mode 波鋒 peak... 這是環境造成的 [xx(] ... 不過, 我還嫌我的系統無法帶給我搥胸口的感受, 當然捨不得去收服它呀... [] [}]

Data-bass 的解說有提到這是 GD 是 system damping 系統減震的問題. 但我這 43Hz 和 50Hz 是環境... 這... 視聽環境可以做減震嗎? 難道要叫我做音場處理嗎? [:I] [/B]


這看你的需求....

但我不玩搥胸口的感受,該有的音效要有,刺激不吵的看電影聽演唱會就好。

謝謝!
[url=http://www.myav.com.tw/market/showthread.php?s=&threadid=5991]進口超值--色差、同軸數位、S線[/url] [url=http://www.myav.com.tw/market/showthread.php?s=&threadid=127614]綜合商品區[/url] [url=http://www.myav.com.tw/market/showthread.php?s=&threadid=20459395]In-akustik 德國敏力線[/url]

226

主題

6231

回帖

100

積分

新手上路

五星級會員

舊站積分
3604
舊站發表文章數
5787
發表於 2017-9-16 18:43:12 | 顯示全部樓層
感謝Chucky兄提供資料.

1. GD的室內測量值在低頻域的觀察價值雖不高, 在音壓與等化調整後可作為輔助. 基本上不要跑出太大的anomoly 聽感上也不容易辨知.

2. Distortion在大音壓的表現可配合頻響觀察:



此圖為例, 在此音量下20hz前後的THD值偏高, 即使20hz左右的基頻在聽覺上不敏感, 其衍生的諧波(頻率更高), 失真量愈大音壓則可能更容易察知.

226

主題

6231

回帖

100

積分

新手上路

五星級會員

舊站積分
3604
舊站發表文章數
5787
發表於 2017-9-16 18:56:54 | 顯示全部樓層
原發表者是 chucky7
[B]


我在 40 ~50 Hz 中間有 room mode 波鋒 peak... 這是環境造成的 [xx(] ... 不過, 我還嫌我的系統無法帶給我搥胸口的感受, 當然捨不得去收服它呀... [] [}]


[:I] [/B]


追求體感的同時犧牲了更均衡的聽感, peak的量感常常帶來的是"單調"(monotonic)的感覺, 遮蔽效應使然, 較低音壓頻率的音效內容也變得更不明顯.

AVS上玩家多以近場擺設增進體感, 適當運用似乎頗有奇效..

34

主題

1311

回帖

0

積分

新手上路

Da Man

舊站積分
1718
舊站發表文章數
1326
 樓主| 發表於 2017-9-16 19:44:08 | 顯示全部樓層
原發表者是 Ken Wu
[B]追求體感的同時犧牲了更均衡的聽感, peak的量感常常帶來的是"單調"(monotonic)的感覺, 遮蔽效應使然, 較低音壓頻率的音效內容也變得更不明顯.

AVS上玩家多以近場擺設增進體感, 適當運用似乎頗有奇效.. [/B]

唉呀... 我是在開玩笑的... [] []

在體感中, 我的視聽空間中要達到 地面和牆壁震動, 抖褲管 和感受到開孔氣流並不難. 但所謂的搥胸口卻沒有在家裡感受過. 上次是 Marc 在做 63Hz CEA 2010 Max Burst, 他叫我站在 Rythmik FV18 前面10 公分的地方我才領教到的. 我看當時音壓搞不好都有 130dB 以上了 [:O] ...



以我的頻響來看, 14~31Hz 和 37~52Hz 這兩段有小幫手, 但是 50~100Hz 這段要到 120dB, 還要多 25 分貝左右. 單單以我現在這顆, 和它目前的所在是辦不到的, 勢必至少要加一台 Cap 1400 近場, 或是添購 2400ULF, 4000ULF 再把 Cap 1400 挪為近場.

所以我還蠻納悶為何其他人那麼容易就可以感受到搥胸口, 他們到底在皇帝位能聽到多大聲 [:O] [] ??? 我很確定我是沒有練過金鐘罩鐵布衫的...[]

34

主題

1311

回帖

0

積分

新手上路

Da Man

舊站積分
1718
舊站發表文章數
1326
 樓主| 發表於 2017-9-16 19:53:21 | 顯示全部樓層
Power Sound Audio 今天公佈了 S7201 的官方 CEA 2010 Max Burst (2M GP RMS) 最大音壓的數據, 還是一樣分成3頻段的平均:

16Hz - 25Hz:         115.1 dB
31Hz - 50Hz:         128.3 dB
63Hz - 100Hz:         133.4 dB

16Hz - 100Hz:         128.2 dB

[:O]

226

主題

6231

回帖

100

積分

新手上路

五星級會員

舊站積分
3604
舊站發表文章數
5787
發表於 2017-9-17 02:07:36 | 顯示全部樓層
原發表者是 chucky7
[B]


在體感中, 我的視聽空間中要達到 地面和牆壁震動, 抖褲管 和感受到開孔氣流並不難. 但所謂的搥胸口卻沒有在家裡感受過.
...

所以我還蠻納悶為何其他人那麼容易就可以感受到搥胸口, 他們到底在皇帝位能聽到多大聲 [:O] [] ??? 我很確定我是沒有練過金鐘罩鐵布衫的...[] [/B]


體感共振與身體構造, 音量都有關係. 這部份很難精算, 想得到的測試方式是利用單頻sine wave訊號地毯式搜索(找屋內低頻共振源也很有效)..

另外提供個人主觀的經驗..

如果聽慣頻響相對平順, 各聲道音壓大致平衡的系統, 且對常測試的低頻片段的音訊spectrum也清楚的話, 應用上在鑑別他處系統的低頻頻響特別是bass 峰值的辨認有頗大幫助(且透過實測做驗證並不困難).

個人聽過某些人稱震撼的系統, 分析過後常得到某些特有的低頻體感明顯多有峰值集中的情況. 漸漸聽得多了除增加經驗值外也學到:

1. "習慣成自然"-- 多數人判斷基準是以主觀因素為主

2. 會搞測量者通常(if not all)系統表現比聽感為憑調整喇叭/超低音者的系統平衡性佳, 鑑別力也強.

以上看法自然也是主觀意見, 這下被"數據派不聽音樂看電影"論者批評的機會又變大了[]

226

主題

6231

回帖

100

積分

新手上路

五星級會員

舊站積分
3604
舊站發表文章數
5787
發表於 2017-9-17 04:18:31 | 顯示全部樓層
補充一下關於Group delay 個人在前頁所述部分:
"GD的室內測量值在低頻域的觀察價值雖不高, 在音壓與等化調整後可作為輔助. 基本上不要跑出太大的anomoly 聽感上也不容易辨知."

關於Group delay 這篇寫得頗清楚, 提供參考.  內文簡介GD 也比較各超低音型式(sealed vs vented..)的表現.

Subwoofer Group Delay (pdf file)

Group delay has been found to be a major predictor of the "tightness" or transient accuracy of a subwoofer
system.
Group delay, in it's mathematical form, is the negative derivative of acoustic phase with respect to frequency.
That is, group delay is a measure of how fast the acoustic phase of the system changes.
Lower group delay numbers are indicative of a "tighter" sound of the subwoofer
(to a certain point; once below a certain threshold, changes in group delay are no longer reliably detectable.
..

Conversely, higher numbers can indicate a "looser" sound


超低音的integration上, 極低頻的聽覺辨知度甚低, 即使在一般測量上會發現調整距離與相位, GD都有相應的變化, 作為檢查的作用, 只要不出現太高的延遲時間都還算可接受.

(另也可參考:Some observations on Group Delay ...and how to minimize its effects in a vented design)
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-19 15:46 , Processed in 0.148110 second(s), 41 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表