忘記密碼
 立即註冊
樓主: ChrisH

談談Milstein的錄音LP

[複製鏈接]

101

主題

2033

回帖

0

積分

新手上路

四星級會員

舊站積分
2320
舊站發表文章數
1545
 樓主| 發表於 2007-7-30 17:16:10 | 顯示全部樓層

Re: Re: 升壓器的機殼

原發表者是 jcc104
[B]

MM實質放大(回復)之前的任何微弱震動(包括磁場)
經過放大之後都會產生很大的干擾
任何銜接點的處理都是學問
以唱臂的重錘來說
重錘和臂管的接觸面必須做damping
唱頭蓋和唱頭接觸面以及螺絲都是震動的來源
包括最敏感的昇壓器的非一體成型部分
請問昇壓器靠近唱臂部分或是MM PHONO部分
原則上是要需要採用較短的訊號線???
[:O] [:O] [:O] [/B]


1.一般廠製昇壓器都會建議到MM PHONO部分訊號線用較短的訊號線越好。這

段線老手會知道要有金屬隔離網(至少一邊接signal ground)的訊號線或同軸式

的訊號線(以隔離網為signal ground),否則易干擾出現哼聲。

2. 【兩吋半的和七吋的】的哪個聲音好?

要以線的電容量加上MM PHONO理面的load電容量的【總合】來說明:

每一種品牌MM PHONO理面的load電容量都不同,有的設計可調,但基本上

會有50pF或100pF的電容,線材有低電容的如一米75pF以下也有一米

200,300多pF的,線越長電容量越高。

那電容量的【總合】要多少pF最佳?真的沒標準答案!原因不贅述。

基本上,電容量太高聽感上會往高頻衰減中低頻變厚,在【中性系統】上細節活

生感減低聲音較呆些,電容量太低則容易使聲音聽起來單薄輕亮些。我個人的經

驗上【總合】約略在250pF到350pF間可找到平衡點。當然還要依不同唱頭的

特性,有些唱頭廠家會建議load多少pF的,另外除了每個人系統的差異性外,

只以一頭一唱放來實驗也容易以偏概全。星期六台中的ED1軟體狂的朋友(非商

家)來訪,我DEMO一些RCA黃金年代的錄音時,本想也來DEMO不同線材不同

刻片的差異及搭配,可惜時間已晚。

線材電容量可以長短來改變,MM phono上電容量也可改變,甚至在

transforner 的secondary後都可加電容調整的選擇。如只談此段線材的長

短,不論金銀銅鐵,【兩吋半的和七吋的】都有可能達到G-spot的。

67

主題

1萬

回帖

0

積分

新手上路

Witch Fly on the Tonearm

舊站積分
7022
舊站發表文章數
12209
發表於 2007-7-30 17:50:08 | 顯示全部樓層

Re: Re: Re: 升壓器的機殼

原發表者是 ChrisH
[B]

1.一般廠製昇壓器都會建議到MM PHONO部分訊號線用較短的訊號線越好。這

段線老手會知道要有金屬隔離網(至少一邊接signal ground)的訊號線或同軸式

的訊號線(以隔離網為signal ground),否則易干擾出現哼聲。

2. 【兩吋半的和七吋的】的哪個聲音好?

要以線的電容量加上MM PHONO理面的load電容量的【總合】來說明:

每一種品牌MM PHONO理面的load電容量都不同,有的設計可調,但基本上

會有50pF或100pF的電容,線材有低電容的如一米75pF以下也有一米

200,300多pF的,線越長電容量越高。

那電容量的【總合】要多少pF最佳?真的沒標準答案!原因不贅述。

基本上,電容量太高聽感上會往高頻衰減中低頻變厚,在【中性系統】上細節活

生感減低聲音較呆些,電容量太低則容易使聲音聽起來單薄輕亮些。我個人的經

驗上【總合】約略在250pF到350pF間可找到平衡點。當然還要依不同唱頭的

特性,有些唱頭廠家會建議load多少pF的,另外除了每個人系統的差異性外,

只以一頭一唱放來實驗也容易以偏概全。星期六台中的ED1軟體狂的朋友(非商

家)來訪,我DEMO一些RCA黃金年代的錄音時,本想也來DEMO不同線材不同

刻片的差異及搭配,可惜時間已晚。

線材電容量可以長短來改變,MM phono上電容量也可改變,甚至在

transforner 的secondary後都可加電容調整的選擇。如只談此段線材的長

短,不論金銀銅鐵,【兩吋半的和七吋的】都有可能達到G-spot的。 [/B]


you mean even a short as 2 and 1/2 inch can reach the G-spot?
No joking.
All women believe "the longer the better."
Anyway, I learn a lot from your post.
[] [] []
站在巨人的肩膀上 我們看得更遠

211

主題

2萬

回帖

150

積分

新手上路

燒膠級會員

舊站積分
9685
舊站發表文章數
21982
發表於 2007-7-30 18:24:49 | 顯示全部樓層

Re: Re: Re: 升壓器的機殼

原發表者是 ChrisH
[B]

1.一般廠製昇壓器都會建議到MM PHONO部分訊號線用較短的訊號線越好。這

段線老手會知道要有金屬隔離網(至少一邊接signal ground)的訊號線或同軸式

的訊號線(以隔離網為signal ground),否則易干擾出現哼聲。

2. 【兩吋半的和七吋的】的哪個聲音好?

要以線的電容量加上MM PHONO理面的load電容量的【總合】來說明:

每一種品牌MM PHONO理面的load電容量都不同,有的設計可調,但基本上

會有50pF或100pF的電容,線材有低電容的如一米75pF以下也有一米

200,300多pF的,線越長電容量越高。

那電容量的【總合】要多少pF最佳?真的沒標準答案!原因不贅述。

基本上,電容量太高聽感上會往高頻衰減中低頻變厚,在【中性系統】上細節活

生感減低聲音較呆些,電容量太低則容易使聲音聽起來單薄輕亮些。我個人的經

驗上【總合】約略在250pF到350pF間可找到平衡點。當然還要依不同唱頭的

特性,有些唱頭廠家會建議load多少pF的,另外除了每個人系統的差異性外,

只以一頭一唱放來實驗也容易以偏概全。星期六台中的ED1軟體狂的朋友(非商

家)來訪,我DEMO一些RCA黃金年代的錄音時,本想也來DEMO不同線材不同

刻片的差異及搭配,可惜時間已晚。

線材電容量可以長短來改變,MM phono上電容量也可改變,甚至在

transforner 的secondary後都可加電容調整的選擇。如只談此段線材的長

短,不論金銀銅鐵,【兩吋半的和七吋的】都有可能達到G-spot的。 [/B]



感謝Chris 兄提供資訊,,

Chris 兄可以具體提供幾款好用的唱臂線嗎?

感謝...
[url=http://www.myav.com.tw/bbs/showthread.php?s=&threadid=272190&perpage=12&pagenumber=290]LP 資料庫索引[/url] [url=https://www.facebook.com/%E4%BD%95%E6%B4%8B%E6%B4%8B%E7%9A%84%E9%9F%B3%E9%9F%BF%E5%AF%A6%E9%A9%97%E5%AE%A4-1147636695299945]何洋洋的音響實驗室[/url]

26

主題

1689

回帖

100

積分

新手上路

四星級會員

舊站積分
3261
舊站發表文章數
1711
發表於 2007-7-31 00:23:26 | 顯示全部樓層

Re: Re: Re: 升壓器的機殼

原發表者是 ChrisH
[B]

1.一般廠製昇壓器都會建議到MM PHONO部分訊號線用較短的訊號線越好。這

段線老手會知道要有金屬隔離網(至少一邊接signal ground)的訊號線或同軸式

的訊號線(以隔離網為signal ground),否則易干擾出現哼聲。
[/B]

I had some discussion of this with Bill Whitlock, the president & chief engineer of Jensen Transformers, in 7/2006.  His suggestion was to keep the distance between the transformer and MM phono stage as short as possible.  The reason being:

1. The cartridge is a low impedance driver.  As long as one keep the wire between the cartridge and the transformer well twisted and shielded, the balanced wire and the low impedance driver makes it relatively resistance to noise.

2. The secondary side of the transformer is a high impedance driver.  The wires used between transformers and MM stages are mostly single ended.  This configuration makes it more noise prong even though signal there has been boosted by 10-20x.

67

主題

1萬

回帖

0

積分

新手上路

Witch Fly on the Tonearm

舊站積分
7022
舊站發表文章數
12209
發表於 2007-7-31 09:03:48 | 顯示全部樓層

Re: Re: Re: Re: 升壓器的機殼

原發表者是 hsindao
[B]
I had some discussion of this with Bill Whitlock, the president & chief engineer of Jensen Transformers, in 7/2006.  His suggestion was to keep the distance between the transformer and MM phono stage as short as possible.  The reason being:

1. The cartridge is a low impedance driver.  As long as one keep the wire between the cartridge and the transformer well twisted and shielded, the balanced wire and the low impedance driver makes it relatively resistance to noise.

2. The secondary side of the transformer is a high impedance driver.  The wires used between transformers and MM stages are mostly single ended.  This configuration makes it more noise prong even though signal there has been boosted by 10-20x. [/B]


The secondary side of the transformer is a high impedance driver.
為什麼?
站在巨人的肩膀上 我們看得更遠

101

主題

2033

回帖

0

積分

新手上路

四星級會員

舊站積分
2320
舊站發表文章數
1545
 樓主| 發表於 2007-7-31 10:08:29 | 顯示全部樓層

Re: Re: Re: Re: 升壓器的機殼

原發表者是 hsindao
[B]
I had some discussion of this with Bill Whitlock, the president & chief engineer of Jensen Transformers, in 7/2006.  His suggestion was to keep the distance between the transformer and MM phono stage as short as possible.  The reason being:

1. The cartridge is a low impedance driver.  As long as one keep the wire between the cartridge and the transformer well twisted and shielded, the balanced wire and the low impedance driver makes it relatively resistance to noise.

2. The secondary side of the transformer is a high impedance driver.  The wires used between transformers and MM stages are mostly single ended.  This configuration makes it more noise prong even though signal there has been boosted by 10-20x. [/B]


To 何兄/hsindao:

What Jensen says is absolutely right.Tim de Paravicini from

EAR,Stevens & Billington,Sowter…,ETC all suggest short length of

cable and that is why I opened with this wording.

However,the【 capacitance 】changes the sound substabtially

which all the trans makers may attribute it to the job of phono

stage makers.Most of the people do not own the adjustable

capacitance MM stage and they can do the change of cables/

capacitance to hit the target,don』t they?You can easily

distinguish sound difference between low capacitance vdH cable

and high capacitance Straight Wire cable when connecting to the

same MM stage.

I prefer to have both primary and secondary leads properly

shielded,there are also 3 types of ground scheme can be

adopted depending on your MM stage circuit.Most of the MC step-

up transformers critically made can be put closer the the electric

power transformer without any hum-pick-up.

26

主題

1689

回帖

100

積分

新手上路

四星級會員

舊站積分
3261
舊站發表文章數
1711
發表於 2007-8-1 02:05:00 | 顯示全部樓層

Re: Re: Re: Re: Re: 升壓器的機殼

原發表者是 jcc104
[B]

The secondary side of the transformer is a high impedance driver.
為什麼? [/B]

It has been discussed somewhere else that a 47K load on the MM phono stage will appear as 47K/10^2 = 470 ohm load on the primary side of the 10X transformer.

On the same token, the output impedance of a cartridge will be amplified by 100x on the secondary side.

67

主題

1萬

回帖

0

積分

新手上路

Witch Fly on the Tonearm

舊站積分
7022
舊站發表文章數
12209
發表於 2007-8-1 09:18:36 | 顯示全部樓層


(cited from Analog)
[;)]
站在巨人的肩膀上 我們看得更遠

101

主題

2033

回帖

0

積分

新手上路

四星級會員

舊站積分
2320
舊站發表文章數
1545
 樓主| 發表於 2007-8-1 10:57:31 | 顯示全部樓層
原發表者是 jcc104
[B]

(cited from Analog)
[;)] [/B]


There are some other excellent essays in this 「analog」 issue,written in Japanese but worth reading.

Here is one of the best MC step-up trans I built myself,now start selling on Ebay.

http://cgi.ebay.com/ws/eBayISAPI ... :MEWA:IT&ih=005

67

主題

1萬

回帖

0

積分

新手上路

Witch Fly on the Tonearm

舊站積分
7022
舊站發表文章數
12209
發表於 2007-8-1 11:09:03 | 顯示全部樓層
原發表者是 ChrisH
[B]

There are some other excellent essays in this 「analog」 issue,written in Japanese but worth reading.

Here is one of the best MC step-up trans I built myself,now start selling on Ebay.

http://cgi.ebay.com/ws/eBayISAPI ... :MEWA:IT&ih=005 [/B]


[] [] []
站在巨人的肩膀上 我們看得更遠
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-20 11:02 , Processed in 0.105050 second(s), 41 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表