新手上路
五星級會員
- 舊站積分
- 3604
- 舊站發表文章數
- 5787
|
發表於 2017-10-21 12:17:29
|
顯示全部樓層
分享舊文: An Interview with Kevin Voecks, Director of Technology, Harman Specialty Group (Revel, Mark Levinson, Lexicon)
Q: When designing a loudspeaker what are the three most important aspects of a loudspeaker according to you that one must get right?
Kevin: Timbre is the overwhelming aspect. Based on our blind listening tests timbre is the thing that differentiates between good and bad loudspeakers, but also between good and great loudspeakers. So timbre is kind of a broad term. It incorporates balance, frequency balance, or it can be thought of very roughly as frequency response. That's a little dangerous because, not to infer that one on-axis measurement tells you what the frequency response is in a loudspeaker. It doesn't. Other areas like off-axis response are very critical and we've learned that very far off-axis response like 60-75 degrees is very critical. Almost no one even measures it, let alone designs loudspeakers that are optimized at that sort of angle. But we've looked at real world situations and found that the all-important side-wall first reflection is a function of the speaker's output at that kind of angle in the vast majority of listening rooms. So it means that you're going to be hearing that kind of sound. You will hear it with a slight delay, and in many rooms without very much attenuation. So optimizing the response at that kind of extreme angle is very, very important. And then the power response, the reverberant field that we hear a little later in time is also important. So we literally design for all of those areas: the direct sound, the first reflection sound, and the reverberant field, because we know that all those three things are huge contributors to the timbre, to our perception of the speaker's timbre.
Q: Would your ideal center channel speaker be the same as the left and right speaker?
Kevin: It's no question the ideal center channel would be the same as the left and right for the best possible timbre match. That's been a problem with home-theater because so far there are no perforated screens that don't ruin the picture even more than the sound. They degrade both, and that is unacceptable. Until and if someone comes up with a screen that is acoustically transparent and doesn't significantly degrade the visual image, we need to use center channels that will fit below a front projector or above or below a rear projector. So we match the timbre as well as possible, and we have adjustments that do a good job of compensating for these various positions. We actually do all of the anechoic measurements and the double blind listening test with the speakers on stands as one condition, sitting on a rear projector TV as another condition, and built in all of those tests to really optimize the response under all of those conditions. I can't imagine anyone else goes to that length.
Q: What are some of the problems that you find in listening rooms?
Kevin: Listening rooms are our biggest problem, clearly, and it's the combination of the way that the loudspeakers interact with the room and the room characteristics overall. Low frequencies are the hardest thing to deal with. They're kind of the most mechanically related thing. So the placement of the loudspeakers and the location of the listeners are extremely critical in a listening room with any loudspeaker, and room treatment at least at mid-range and high-frequencies is really critical. While our speakers have very accurate (response) even way far off-axis, it's still greatly preferable to properly treat the first reflection points in the room.
We know from our research that the first reflection points are audibly very critical, and especially the side wall reflection points. So I like to see absorption, at those first reflection points, at least unless the room is quite large, and otherwise diffusion in the room overall. For imaging characteristics it's optimum to be sitting on the center line, but that introduces challenges at low frequencies in most rooms which can be accommodated by diaphragmatic absorbers to the side or the use of multiple subwoofers, and our work is on-going. We've got some great results using multiple subwoofers in order to solve problems of dips in response that you can't solve with any single subwoofer location, and also getting consistency of response throughout the listening area.
Q: This leads into my next question on the use of multiple subwoofers. Do you recommend that?
Kevin: Absolutely. We've done really quite definitive research on that, and we found the optimum number of subwoofers is four, and you get a huge improvement in most rooms going from one to two subwoofers. |
|