忘記密碼
 立即註冊
樓主: Brachy

Ekta DIY 筆記

[複製鏈接]

197

主題

3310

回帖

50

積分

新手上路

四星級會員

舊站積分
1198
舊站發表文章數
2511
 樓主| 發表於 2008-2-13 21:17:53 | 顯示全部樓層

Ekta Grande單體的基本測試 - 18W8531 part 3

Ekta Grande單體的基本測試 - 18W8531: part 3

未裝箱:


圖一: 裝箱後有幾項相當重要的變化

1. 阻抗高峰大幅下降
2. 阻抗高峰處向下移動, 18w8531自40 Hz 降至 30 Hz, 代表裝箱後諧振
       下降至30 Hz, 嗯, 這是好事!
3. Phase angle 變窄, 這也是好事!

圖二: 這圖很多人可能猜不中, 教課書上也沒有喔!

這是兩支18W8531併聯之實測圖!
阻抗高峰又進一步下降, 對擴大器當然是好事但要注意其平均阻抗也下降,
必須注意擴大器是否可以長時間用4 甌姆輸出. Dickason有詳細描述雙低音
的優點在此不再累述. [] []

雙低音與單低音的聽感呢? 哈哈哈, 底盤穩定許多而且更具權威感! []
聲音, 自己喜歡就好! 幸福, 就是有好老師! [:)]

197

主題

3310

回帖

50

積分

新手上路

四星級會員

舊站積分
1198
舊站發表文章數
2511
 樓主| 發表於 2008-2-14 20:37:32 | 顯示全部樓層

Ekta Grande的整體與各單體響應

各單體的響應頻率:


一起合作後:


電子分音器分頻點確實是780 Hz 與3.8 kHz, 看斜率也應該是4階, 似乎這線路
與精準度都還不錯! 最左黃色的曲線是調整後的超低音, 分頻點差不多是50

Hz. 我發現超低音的分頻點的標示僅供參考, 弟有兩顆都不準必須自己測試再
調整才OK! 難怪以前常常覺得自己的超低音很難聽不好調, 原來是標示不準.

在ATB PC pro的輔助下就好調整多了, 而且最後人耳驗收時非常自然完全
不覺得有開超低音但極低頻又延伸無礙!!

在弟的系統, 目前似乎達到20 ~ 18 kHz ± 6 dB的目標.!!
[] []
聲音, 自己喜歡就好! 幸福, 就是有好老師! [:)]

197

主題

3310

回帖

50

積分

新手上路

四星級會員

舊站積分
1198
舊站發表文章數
2511
 樓主| 發表於 2008-2-14 20:46:30 | 顯示全部樓層

Re: Ekta Grande的整體與各單體響應

暫時不想動喇叭位置, 下一步就是利用Velodyne SMS-1來補償150 Hz

8~9 dB 的凹陷了.

本想利用儀器輔助設計電子分音後再加上各單體的頻率或阻抗補償線路,

測試結果發現這些單體與現有器材搭配的表現實在不需要這些線路,

反倒是對於調整整體頻率響應與搭配超低音幫助頗大!! []
聲音, 自己喜歡就好! 幸福, 就是有好老師! [:)]

197

主題

3310

回帖

50

積分

新手上路

四星級會員

舊站積分
1198
舊站發表文章數
2511
 樓主| 發表於 2008-2-14 20:55:07 | 顯示全部樓層

B&W 800s的響應



沒有要討論聲音喜好, 這是登在Stereophile B&W 800S的響應,

以1 k Hz做標準, ± 6 dB大概為26 ~ 20 kHz. 看的出來它的中低頻量感是

很豐富的!

但是由阻抗分佈曲線就知道不是好對付的喇叭喔!
聲音, 自己喜歡就好! 幸福, 就是有好老師! [:)]

19

主題

2414

回帖

0

積分

新手上路

三星級會員

舊站積分
5082
舊站發表文章數
578
發表於 2008-2-15 03:20:12 | 顯示全部樓層

Re: Re: 回應150 Hz處凹陷問題, Part 3 反射孔篇

原發表者是 Brachy
[B]Part 3
這些響應曲線是反射孔的實測圖, 原設計反射孔的頻率為33Hz, 實測為30 Hz
表示設計與施工均很"正確". (現在不太敢用正確兩字怕嗆聲, 哈哈!)
...
每個環境與系統會組合成非常獨特的響應, 小張在反射孔放吸管對於老李卻
不一定有效喔! 我發現的方法最好只能說在某特定環境組合才有效, 不能宣稱
他人方法不對只有自己才是對的喔!!
[|)] [:I] [/B]


哈哈,新年期間小弟和老朋友們抬槓("正確")
讓Brachy兄見笑了[]

Bean會設計、製作頻譜分析儀,那是他的專長(之一?)
小弟幫您招呼一聲
看他有沒有空來捧場[]

20

主題

4368

回帖

0

積分

新手上路

五星級會員

舊站積分
508
舊站發表文章數
4372
發表於 2008-2-15 10:02:42 | 顯示全部樓層

Re: Ekta Grande單體的基本測試 - 18W8531

原發表者是 Brachy
[B]Ekta Grande單體的基本測試 - 18W8531

先show 在未裝箱的數據:


原廠規格fs=28 Hz (看原廠測試圖為 ~ 33 Hz), 弟這支實測40 Hz,
其實這都是可接受的範圍!

Troels有提到這顆單體是他用過與測試過低音與高頻延伸最好的七吋單體!
發聲範圍極廣, 自fs ~ 5k Hz 沒問題!

Phase angle 20 Hz ~ 10 kHz 均小於45 度!!

[] [/B]

Your recording channels seem to have some interchannel latency.  If you can show your setup connection.  I can have a look.  What software are you using?

Edit:
Looked at the manual.  This is a funny way of testing.  But the impedance phase is not correct.  Don't know what kind of signal is used for the measurements, so really can't tell what's going on.
[url="http://augene.blogspot.com"]Hear The REAL Thing[/url] [url="http://www.augene-audio.com.tw"]感受藝人的心靈[/url]

197

主題

3310

回帖

50

積分

新手上路

四星級會員

舊站積分
1198
舊站發表文章數
2511
 樓主| 發表於 2008-2-15 13:15:35 | 顯示全部樓層

Re: Re: Re: 回應150 Hz處凹陷問題, Part 3 反射孔篇

原發表者是 Patrick
[B]

哈哈,新年期間小弟和老朋友們抬槓("正確")
讓Brachy兄見笑了[]

Bean會設計、製作頻譜分析儀,那是他的專長(之一?)
小弟幫您招呼一聲
看他有沒有空來捧場[] [/B]


感謝再感謝!! []

Bean大與Patrick兄請先受小弟一拜託!  []
聲音, 自己喜歡就好! 幸福, 就是有好老師! [:)]

197

主題

3310

回帖

50

積分

新手上路

四星級會員

舊站積分
1198
舊站發表文章數
2511
 樓主| 發表於 2008-2-15 13:24:50 | 顯示全部樓層

Re: Re: Ekta Grande單體的基本測試 - 18W8531

原發表者是 soongsc
[B]
Your recording channels seem to have some interchannel latency.  If you can show your setup connection.  I can have a look.  What software are you using?

Edit:
Looked at the manual.  This is a funny way of testing.  But the impedance phase is not correct.  Don't know what kind of signal is used for the measurements, so really can't tell what's going on. [/B]


Thanks a lot for your nice comment!

I used ATB-PC pro software for testing. I knew that this is just a
toy comparing to other professional testing software. However,
an amateur like me just could afford this kind of measurement
tool.

Sorry, I did not know why is "interchannel latency"? What you see
was just the results of one speaker.

I'll show my set-up after I get home. []
聲音, 自己喜歡就好! 幸福, 就是有好老師! [:)]

20

主題

4368

回帖

0

積分

新手上路

五星級會員

舊站積分
508
舊站發表文章數
4372
發表於 2008-2-15 14:49:43 | 顯示全部樓層

Re: Re: Re: Ekta Grande單體的基本測試 - 18W8531

原發表者是 Brachy
[B]

Thanks a lot for your nice comment!

I used ATB-PC pro software for testing. I knew that this is just a
toy comparing to other professional testing software. However,
an amateur like me just could afford this kind of measurement
tool.

Sorry, I did not know why is "interchannel latency"? What you see
was just the results of one speaker.

I'll show my set-up after I get home. [] [/B]

Normally the impedance phase above the 1KHz range should be pretty flat.  It would either be close to zero or close to 45 degrees depending one the motor structure.  The droop above 1KHz suggests an interchannel latency if two input channels are used (one as reference and one as data).  If the phase goes up after this frequency in a straight manner, the interchannel latency is in a different direction. I would recommend SpeakerWorkshop if you are looking for freeware.  For full design, SoundEasy is the best bang for the buck.  both of these will require some learning, but will be worth it if someone is really getting serious in design.

Interchannel latency is sound card dependent.  Normally the better recording cards don't have this problem.
[url="http://augene.blogspot.com"]Hear The REAL Thing[/url] [url="http://www.augene-audio.com.tw"]感受藝人的心靈[/url]

197

主題

3310

回帖

50

積分

新手上路

四星級會員

舊站積分
1198
舊站發表文章數
2511
 樓主| 發表於 2008-2-15 20:07:50 | 顯示全部樓層

Re: Re: Re: Re: Ekta Grande單體的基本測試 - 18W8531

原發表者是 soongsc
[B]
Normally the impedance phase above the 1KHz range should be pretty flat.  It would either be close to zero or close to 45 degrees depending one the motor structure.  The droop above 1KHz suggests an interchannel latency if two input channels are used (one as reference and one as data).  If the phase goes up after this frequency in a straight manner, the interchannel latency is in a different direction. I would recommend SpeakerWorkshop if you are looking for freeware.  For full design, SoundEasy is the best bang for the buck.  both of these will require some learning, but will be worth it if someone is really getting serious in design.

Interchannel latency is sound card dependent.  Normally the better recording cards don't have this problem. [/B]


弟回來查了一下測試方式確認無誤, 請再看一下底下:

我們由phase angle 上下劇烈擺動的位置在40 Hz左右可以判斷這個部分
是正確的沒問題, 測量方法也應無誤否則無法量出這樣曲線. 唯一有疑問處
在超過4KHz phase angle 下降的問題. 這確實有可能是導因於軟體或PC
音效卡或其他問題.

至於1 kHz以上是否phase 一定會平直也不一定, 下面舉兩例就知:
http://www.stereophile.com/standloudspeakers/405epos/index3.html
Epos M5 的圖 一

或 Elliott 模擬的speaker phase angle 變化 (圖四):
http://sound.westhost.com/patd.htm

當然對低音單體來說應該1 ~ 10 kHz以上angle 上揚應居多才對....

非常謝謝您的精明的意見與厲害的眼力讓弟又多瞭解了一些! [] []
聲音, 自己喜歡就好! 幸福, 就是有好老師! [:)]
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-19 00:05 , Processed in 0.183525 second(s), 41 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表