忘記密碼
 立即註冊
樓主: leon88

聽說這是一顆聽了會中毒的重音 Seaton Submersive

[複製鏈接]

145

主題

2629

回帖

0

積分

新手上路

四星級會員

舊站積分
793
舊站發表文章數
2157
 樓主| 發表於 2010-11-12 16:15:03 | 顯示全部樓層

Re: 補充新進度.

原發表者是 Ken Wu
[B]七月初等到今天. 又是一百多天ㄟ等待[)]

右為submersive HP 2.4kW amp, 左為拆下的subm 原1kW的amp.




鬆開螺絲, 再"使勁"拆下後, 簡單插拔即可更換.



兩顆subM HP 同時發功, 初步印象是極低頻延伸更輕鬆, 更大的動態與更高的密度感.

可惜這HP版尚無220V 版本. [/B]



所以應該可以排時間來作13AV.2 2000W  VS   Submersive 2000W 的測試了[]
[URL=http://www.myav.com.tw/bbs/showthread.php?s=&threadid=421175&perpage=12&pagenumber=1]時光鏡[/URL]

226

主題

6231

回帖

100

積分

新手上路

五星級會員

舊站積分
3604
舊站發表文章數
5787
發表於 2010-12-17 03:22:30 | 顯示全部樓層
原發表者是 Ken Wu
[B]貼幾張現有REW低頻頻譜(1/3 Oct 平滑化)再給諸君娛樂一下[]
雙低音共同發聲: Submersive/G900 (Master/slave, High Pass :Submersive 9Hz, G900 21Hz 24dB/Oct)

由上至下五處測量: 右,  中,  左.
[/B]


貼幾張這陣子調整的2x submersive HP 頻響圖, 來與先前的做粗略比較.
注意平滑化顯示程度略有不同: before 1/3 Oct, after 1/6 Oct.


1.
右側座位, before. (submersive +G900, 用EQ 調相位與壓低20Hz以下波峰, 1/3 Oct 平滑化)==>




右側座位, after. ( 2 submersive HPs, 僅用EQ 調相位, 1/ 6 Oct 平滑化 )==>



2.
中央座位, before. (submersive +G900, 用EQ 調相位與壓低20Hz以下波峰, 1/3 Oct 平滑化)==>




中央座位, after. ( 2 submersive HPs, 僅用EQ 調相位, 1/ 6 Oct 平滑化 )==>



3.
左側座位, before. (submersive +G900, 用EQ 調相位與壓低20Hz以下波峰, 1/3 Oct 平滑化)==>




左側座位, after. ( 2 submersive HPs, 僅用EQ 調相位, 1/ 6 Oct 平滑化 )==>




目標是在不作等化的前題下, 讓中央位置的頻響更平順.
這空間可觀察到20~40Hz明顯的頻率增幅與抵消問題 (20Hz以下由於測量可信度低, 也暫不予調整).

用兩顆同樣的超低音調整起來, 比之前能力不相近的是要容易得多.

submersive HP  多了一個DSP模式可容許更低的延伸, 切換時確實可以在頻譜上看到差別.
規格上 1kw subM 19-200Hz (+/-3dB ), 切至該DSP 模式的 subM HP 則是15-200Hz .
(請參考 此討論串)

個人的系統聽感上, 以單顆相比, 雖然原有的1kw subM 便已提供足夠的低頻餘裕度,
換成2.4kw 的 subM HP 仍確實可以感受到差別.
尤其是切到該(加強延伸)DSP 模式時, 對於較大空間,極低頻需求大的demo片段, 感受會較明顯.

226

主題

6231

回帖

100

積分

新手上路

五星級會員

舊站積分
3604
舊站發表文章數
5787
發表於 2010-12-29 23:21:51 | 顯示全部樓層
跟ups 兄借了支Earthworks mic, 來跟SMS-1 用的ECM8000 比較一下.
看來這支ecm8000在2kHz以下,不要套用校正檔反而較準.
給當天測試的朋友們參考! 在此感謝ups兄!

226

主題

6231

回帖

100

積分

新手上路

五星級會員

舊站積分
3604
舊站發表文章數
5787
發表於 2015-9-3 14:59:41 | 顯示全部樓層
把這串老文挖出來透透氣[]

翻了下之前寫的, 不禁有些今夕何夕之感. 歷經幾次改款都快十年的產品了居然到今日才看得到器評, 而其它定位類似的網售為主的商品也早已推陳出新, 百花齊放.
Seaton 聲稱這一兩年將陸續推出新貨包括各式主動式喇叭與雙18"等, 其實這幾年競爭對手是愈來愈多了, 再慢下去會更趨飽和了. 除幾年前曾在HK出現過國外代理外, Seaton 的腳步也實在太保守了些.

雖然此評不算周全, 有興趣者不妨翻閱參考.

First formal review of the Seaton SubMersive by Secrets of HT and Hi-fi

43

主題

1298

回帖

0

積分

新手上路

四星級會員

舊站積分
1114
舊站發表文章數
1004
發表於 2015-9-3 15:37:24 | 顯示全部樓層
此顆極低頻實在驚人,原廠公佈的數據與實際聽感一致。全台應該只有Ken 兄兩顆

站上許多號稱低頻量感多麼優秀的超低音,實際測試表現真不知如何? MYAV其實可以找到滿多客觀超低音性能討論,但不知為何還是常聽見許多玩劇院的玩家們會說"某某顆超低音少了哪一段沒什麼感覺",以主觀感覺認知評斷超低音性能的還是一樣不在少數。
-數據才是調整的開始-

226

主題

6231

回帖

100

積分

新手上路

五星級會員

舊站積分
3604
舊站發表文章數
5787
發表於 2015-9-3 17:39:12 | 顯示全部樓層
原發表者是 jimchao
[B]此顆極低頻實在驚人,原廠公佈的數據與實際聽感一致。全台應該只有Ken 兄兩顆

站上許多號稱低頻量感多麼優秀的超低音,實際測試表現真不知如何? MYAV其實可以找到滿多客觀超低音性能討論,但不知為何還是常聽見許多玩劇院的玩家們會說"某某顆超低音少了哪一段沒什麼感覺",以主觀感覺認知評斷超低音性能的還是一樣不在少數。 [/B]


本地用家應該不只一位啦. 只是用家都不太發聲惦惦玩.
倒是其它的網上近來較紅的品牌(如JTR 等) 較少看到本地用家, 對這類品牌性能頗為好奇.

145

主題

2629

回帖

0

積分

新手上路

四星級會員

舊站積分
793
舊站發表文章數
2157
 樓主| 發表於 2015-9-9 18:31:31 | 顯示全部樓層
原發表者是 Ken Wu
[B]

本地用家應該不只一位啦. 只是用家都不太發聲惦惦玩.
倒是其它的網上近來較紅的品牌(如JTR 等) 較少看到本地用家, 對這類品牌性能頗為好奇. [/B]



可能是論壇漸漸變神壇,太多的神蹟佔滿版面

沒有特異功能的玩家會選擇惦惦的玩,低調的好處就是看著論壇倒退十年,自己的器材就能再保持領先十年了
[URL=http://www.myav.com.tw/bbs/showthread.php?s=&threadid=421175&perpage=12&pagenumber=1]時光鏡[/URL]

226

主題

6231

回帖

100

積分

新手上路

五星級會員

舊站積分
3604
舊站發表文章數
5787
發表於 2015-10-11 11:58:42 | 顯示全部樓層
趁著假日做了室內極限音壓簡測, 由音壓計75dB 開始, 前級每增加5dB紀錄一次, 結果如下.


利用REW 以mic pre+ECM8000 mic 擷取, 將mic pre gain 調低使訊號低至-30dB FS 保留餘裕度 最後到約100dB(15dB above reference) 時REW 開始clipping 才停止.
約12hz以下的異常應該是有limiter 發生作用. 看到曲線的異常後還反覆測了兩次, 出現高於20Hz的那些dips 的起伏就不是我能解釋的.
或許與我之前測過,與其它test tone 測量比較的差異有關?
另音量大到約13db above reference會開始聽得到單體動作聲. Seaton 曾提過submersive 上有設定high pass limiter

以上提供參考.

226

主題

6231

回帖

100

積分

新手上路

五星級會員

舊站積分
3604
舊站發表文章數
5787
發表於 2015-11-2 14:25:33 | 顯示全部樓層
Submersive的擴大機版升級了! 新的功能包括rca/平衡版輸入並存 增加低通crossover以利兩聲道/多聲道使用,delay time, 音量調整範圍增大等.未來的雙18」新品也會配置這機板.
搭配另外不具後級amp的slave unit 輕鬆實現多顆超低音的夢想.

1. 12V trigger and auto sensing: There are 12V trigger power devices available for ~$100. Those switch to 100% off, where the on-board 12V trigger gets to 1/4-1/3rd of idle power and eliminates any chance of induced noise while the system is off.

2. LF EQ (low shelf/adjust extension/room size fitting): If you have flexible manual EQ in the system in theory you can implement most of what the program settings and LF EQ offers, but many don't or won't get quite the right shape of things where this makes it very easy to dial in whatever lift/house curve you are after.

3. Delay adjustment 0-20ms: If you have a single powered unit being used with a modern surround processor, the delay adjustment isn't of much advantage. For those with more than one powered subwoofer, the delay function could allow someone to eliminate a device and A/D-D/A step in an external box like a MiniDSP or DSP-30, particularly if you already have a room correction system like Audyssey XT32 or Dirac. For Dirac this is a significant advantage when using multiple powered units as it is much better equipped to correct the response of the subwoofers as a group after you first adjust placement and delay to get a good summation and starting point. Even though Audyssey XT32 does attempt to apply delay, it still EQ's the subs as a whole, and I have always found better results if the delay and blending is done manually and then let Audyssey correct the whole.

4. Low pass crossover 30-120Hz + 200Hz: The new amplifier adds a 4th order (24dB/octave) low pass filter. While I very much prefer for 2ch listeners to have some form of response correction in the system to get the best sound quality, this opens many more possibilities in 2ch systems where you can use devices such as DSPeaker's AntiMode products or MiniDSP's Dirac boxes which don't include a low pass. You can also use the internal low pass to get a workable blend with the speakers and then use a single, full-range correction system such as Dirac, Trinnov, or AntiMode Dual-Core. Having a low pass at the amplifier can sometimes makes for a useful added flexibility in a home theater setup when blending multiple units or taming some in-room peaks just above the operating range. If the delay adjustment didn't quite get rid of some localization of a rear subwoofer, or you're having trouble getting a good blend with only delay adjustment, sometimes a low pass can work on its own or in combo with less overall delay as the low pass filter has some inherent delay of its own that changes with frequency to give a little different blend and less upper frequency contribution.

5. XLR & RCA inputs: No need for adapters. While those who know they will eventually have a preamp with XLR connections might still want to run an XLR cable and use adapters, the best practice will be connecting XLR-XLR & RCA-RCA. This gives the lowest probability of hum or buzz. These higher power models do need to still use the 3rd pin safety ground, but addressing ground loop issues in an XLR-XLR system is typically a much simpler matter of just grounding the preamp.

0

主題

1

回帖

0

積分

新手上路

初級會員

舊站積分
0
舊站發表文章數
1
發表於 2015-11-18 17:58:28 | 顯示全部樓層
初來報道。。。。
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-18 23:52 , Processed in 0.122024 second(s), 41 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表