忘記密碼
 立即註冊
樓主: jcc104

LP唱臂

[複製鏈接]

101

主題

2033

回帖

0

積分

新手上路

四星級會員

舊站積分
2320
舊站發表文章數
1545
發表於 2006-12-11 17:26:32 | 顯示全部樓層
原發表者是 ChrisH
[B]

alc 真的是跟我一樣認真的人,雖然有時候比我還要認真,然後認真過頭了。但是不管怎麼說,他認真我總是很高興的,尤其是他辛苦的找資料、做實驗,然後把心得跟我們分享時,我真想頒一個「義工」獎章給他...  []

alc這篇文章老實說寫得不錯,要挑毛病的地方真的不多!但之前看到」 請吐槽。
[] "非常引起我的興趣! [/B]


"抗滑"似乎會越挖越明白![]

我先請教alc,下面這段話是VPI說的嗎?

quote by alc:
傳統臂因為有循軌誤差,除了 null points 之外,唱針和溝槽都不成正切,這導致了向內或向外的分立產生。 在 null point A~B 之間,這個分力向內,A、B 的外側則是向外的分力。 因為音樂大多數位於 A~B 之間,所以唱臂的設計者就妥協性的做了一個向外拉的 Anti-skate 調整。 也有唱臂不做這個的,如 VPI 的 JMW arm. 設計者說用抗滑沒什麼道理,建議加一點針壓來解決。

嚴格說來,這個抗滑真的沒什麼道理。過了 null point B 再往內圈時,唱頭本身的循軌誤差已經讓它自身產生了一個向外的分力,此時抗滑若是再把唱頭往外拉,無異雪上加霜。
unguote

******************

1.假設null points A 與 B 這兩點正切,此時的 offset angle為23.85度.

2.從唱片外圓到A點這段offset angle大於23.85度且成遞減.

3.從A 到 B這段offset angle 是小於A 點 的 offset angle 且成遞減,到AB 中間再過去ㄧ些的地方(如null points約為66mm與121mm則大約在86mm) ,又開始遞增.(12/11 21:00 revised)

4.從B到最內這段offset angle大於23.85度且成遞增.

前面skating force的公式offset angle的大小會如何影響,大家用腦筋想一下!
[;)]

*************************

quote by wecare:

回轉力=μ*W*sinΦ (磨擦係數 針壓 補償角)


抗滑 與 針尖 對 唱片溝槽 的 動摩擦係數 成正比

所以與針尖的形狀與大小有關

我猜想

貴的唱頭 因針尖較小 摩擦力小 因此 內滑力比 便宜、大針尖的唱頭小

古代的半圓針尖 因接觸面積小 內滑力最小

超橢圓針 內滑力 比 半圓針大

Micro-Ridge 針尖的內滑力 又比 超橢圓針尖大

因為多了兩片翅膀


結論是抗滑的調整 沒有定數

一切耳聽為憑
unquote

************************

除了"貴的唱頭 因針尖較小"這句話不對外其他都說的很好!
除了offset angle影響 skating force外,針壓,針尖與groove的接觸面積不是一個常數會隨高低頻改變........所以說wecare兄如能發明幾個恆等式出來我要替他申請諾貝爾獎,以及我說"一種compromise,and can be different from records to records and grooves to grooves.

167

主題

8萬

回帖

0

積分

新手上路

五星級會員

舊站積分
32767
舊站發表文章數
11966
發表於 2006-12-11 17:31:29 | 顯示全部樓層
原發表者是 ChrisH
[B]


除了"貴的唱頭 因針尖較小"這句話不對外其他都說的很好!
. [/B]


較貴的唱頭 「通常」 針尖尺寸 較小

[] []

67

主題

1萬

回帖

0

積分

新手上路

Witch Fly on the Tonearm

舊站積分
7022
舊站發表文章數
12209
 樓主| 發表於 2006-12-11 18:10:10 | 顯示全部樓層
原發表者是 alc
[B]

我的認知是:

唱頭本身只有做一個很緩慢向圓心的運動,其緩慢之程度,比起

唱片不圓引起的左右漂移
唱片不平引起的上下彈跳

來說,實在不足為道,可以將之忽略。


再次

歡迎 (Chris) 吐槽 []

要說真悟還是半悟,我想至多七成,裡面相關的物理原理我不太想再花時間了。弄清楚 skating force 是從循軌不良來的,弄清楚它的方向,對我來說就夠用了。 要徹底解決這件事,我看不是直切臂,就是雷射唱盤。

我還有一個考題,不過我想先等 Tien 兄和 Hsindao 的唱頭討論告一段落,再來鬧場。 [/B]


Alc兄
問題的起源在於」向心力」
我讀的日文(很老)報告從沒提到向心力
只有」回轉力=μ*W*sinΦ」
而且也附上圖說明
***
唱頭看起來好像繞著唱盤中心」轉」
(姑且不論誤差 就當是同心圓好了)
但是唱頭從來就不是繞著唱盤中心運動的」自由」物體
(所謂的圓周運動)
是唱盤在轉
您忘了它只是唱臂上一個」支點」
唱臂上另有一個真正的支撐點拉著唱頭
唱頭只是以唱臂支撐點做小幅度的運動
(當然是唱盤溝槽帶動的)
所以唱頭跟本沒做圓周運動
只是被迫延著唱盤中心慢慢移動
跟本不符合圓周運動的條件
當然無所謂向心力的問題
站在巨人的肩膀上 我們看得更遠

151

主題

8413

回帖

0

積分

新手上路

五星級會員

舊站積分
24833
舊站發表文章數
7074
發表於 2006-12-11 18:13:51 | 顯示全部樓層
先回 Chris 對 VPI JMW arm 的疑問

from http://72.14.235.104/search?q=cache:UppAuGwUeJwJ:[url]www.vpiindustries.com/pdf/JMW_12.6_Manual.pdf+skating+force&hl=zh-TW&ct=clnk&cd=5[/url]

E. ANTI-SKATING:

‧ A pivoted arm without an offset head would not be subject to skating force. However, it will also have no correction for tracking error and the resulting distortion is unacceptable. As soon as the arm's head is offset to lower tracing distortion, skating force arises. Greater offsets result in greater skating force. The 12」 arm has a very small offset angle and therefore a very low skating force to deal with.

‧ After very careful listening tests we have determined that every tonearm we tried sounded better with their mechanical anti-skating disabled and the tracking force very slightly increased. All mechanical anti-skate devices add a negative sound to the music because they are made of parts that can vibrate. We solve the problem in a unique way:

‧ As mentioned earlier, the arm wire applies the anti-skating force. The degree of force applied can be adjusted as explained below.

‧ To increase or decrease the amount of anti-skating force applied, simply unplug the Lemo connector and twist it in the direction you want the force applied.

‧ For example, to increase anti-skating force give the connector a counterclockwise twist, unwinding the coiled wire. Likewise, to decrease the force, give the connector a clockwise twist. Remember, the Lemo connector can only be "adjusted" in increments of whole turns. If it is not, its key will not line up with the groove in the receptacle.

‧ We could go on discussing the pros and cons of how much anti-skate is correct, but the sonic answer is very simple. Adjust the wire as mentioned above until the tonearm drifts outward when set to neutral balance. When you push the neutral balance floating tonearm towards the center of the record, it should push back out towards the rim of the record. Very little force is needed to do this, and the wire acts like a spring to supply this force.

‧ If you try adjusting the anti-skate with a groove less record or a test record you will ruin the twist in the wire and void your warrantee

‧ Double check the horizontal balance, lateral balance, and tracking force and adjust as needed. Increase the tracking force by 1/10 of a gram above the cartridge manufacturers highest recommended force.


摘要:

1. 12" arm 的 offset angle 小,故 skating force 小.

2. 聆聽其他唱臂的結果,發現拿掉 anti-skating ,略增針壓聲音較好。

3. 用唱臂訊號線來做抗滑。(twist it!)


151

主題

8413

回帖

0

積分

新手上路

五星級會員

舊站積分
24833
舊站發表文章數
7074
發表於 2006-12-11 18:16:10 | 顯示全部樓層
原發表者是 jcc104
[B]

Alc兄
問題的起源在於」向心力」
我讀的日文(很老)報告從沒提到向心力
只有」回轉力=μ*W*sinΦ」
而且也附上圖說明
***
唱頭看起來好像繞著唱盤中心」轉」
(姑且不論誤差 就當是同心圓好了)
但是唱頭從來就不是繞著唱盤中心運動的」自由」物體
(所謂的圓周運動)
是唱盤在轉
您忘了它只是唱臂上一個」支點」
唱臂上另有一個真正的支撐點拉著唱頭
唱頭只是以唱臂支撐點做小幅度的運動
(當然是唱盤溝槽帶動的)
所以唱頭跟本沒做圓周運動
只是被迫延著唱盤中心慢慢移動
跟本不符合圓周運動的條件
當然無所謂向心力的問題 [/B]


好,你解套了,剩何醫師? []

101

主題

2033

回帖

0

積分

新手上路

四星級會員

舊站積分
2320
舊站發表文章數
1545
發表於 2006-12-11 18:17:30 | 顯示全部樓層
原發表者是 wecare
[B]

較貴的唱頭 「通常」 針尖尺寸 較小

[] [] [/B]


厚~~你動作很快耶!
[:O]

我猜你開車跟lvt2006一樣快!
喜歡"精準"的LP聲音!
對否?

167

主題

8萬

回帖

0

積分

新手上路

五星級會員

舊站積分
32767
舊站發表文章數
11966
發表於 2006-12-11 18:25:38 | 顯示全部樓層
原發表者是 ChrisH
[B]

厚~~你動作很快耶!
[:O]

我猜你開車跟lvt2006一樣快!
? [/B]



年紀大了 眼睛不好

車越來越貴

車速越來越慢

suhumi 開得比較快

[] []

167

主題

8萬

回帖

0

積分

新手上路

五星級會員

舊站積分
32767
舊站發表文章數
11966
發表於 2006-12-11 18:27:48 | 顯示全部樓層
原發表者是 ChrisH
[B]

厚~~你動作很快耶!
[:O]

喜歡"精準"的LP聲音!
對否? [/B]


精準 而不失 甜美 溫潤 的聲音

我是管機派的

[] []

151

主題

8413

回帖

0

積分

新手上路

五星級會員

舊站積分
24833
舊站發表文章數
7074
發表於 2006-12-11 18:29:47 | 顯示全部樓層
原發表者是 ChrisH
[B]

...

******************

1.假設null points A 與 B 這兩點正切,此時的 offset angle為23.85度.

2.從唱片外圓到A點這段offset angle大於23.85度且成遞減.

3.從A 到 B這段offset angle小於23.85度且成遞減.

4.從B到最內這段offset angle大於23.85度且成遞增.

...
...
...[/B]


Chris, 有幾點討論一下

offset angle 在越長的臂應該越小。


從從A 到 B這段offset angle 應該是小於A 點 的 offset angle 且成遞減,到AB 中間再過去ㄧ些的地方,又開始遞增至 B 點 的 offset angle.

101

主題

2033

回帖

0

積分

新手上路

四星級會員

舊站積分
2320
舊站發表文章數
1545
發表於 2006-12-11 18:38:14 | 顯示全部樓層
原發表者是 alc
[B]

Chris, 有幾點討論一下

offset angle 在越長的臂應該越小。


從從A 到 B這段offset angle 應該是小於A 點 的 offset angle 且成遞減,到AB 中間再過去ㄧ些的地方,又開始遞增至 B 點 的 offset angle. [/B]




offset angle 在越長的臂應該越小。>>>Yes!廢話



I am on the way home!see you on this forum tonight.!
ChrisH


回家再仔細看!你說對了!
從A 到 B這段offset angle 是小於A 點 的 offset angle 且成遞減,到AB 中間再過去ㄧ些的地方(如null points約為66mm與121mm則大約在86mm) ,又開始遞增.

前面已修正.
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-20 10:12 , Processed in 0.165950 second(s), 41 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表