新手上路
四星級會員
- 舊站積分
- 283
- 舊站發表文章數
- 2047
|
樓主 |
發表於 2005-10-27 16:32:27
|
顯示全部樓層
原發表者是 Masa
[B]市面上不少擴大器也採用 a main amplifire with input selector and level control 這種設計,只是ASR把這概念進一步提升到巨大而且分離的電源設計。
本地不少人好像都認為擴大器採前後級分離會比較好,所以都覺得綜擴等級不夠。但前後級匹配不良衰聲的機率更高,如果訊號線與電源線又做錯選擇,那結果更是悽慘。
所以一部設計優良的綜擴根本不會比前後級差,加上能把原本需花在前級的線材預算挪來買一套更高檔的訊號線與電源線,樂趣更多呢~
而且像ASR這種龐大的分離電源設計已超越一般的前後級許多,所以不一定得搞前後級才會好玩啦! [/B]
呼應一下Airstream兄及Masa兄的說法.
以下截錄自ASR原廠對前級和音控的說明,很有參考價值,希望有助於對ASR設計理念的瞭解.
1) What functions does the pre-amplifier do in home hifi systems ?
Before the CD era, a full function pre-amplifier is essential for a home stereo system. It receives signals from source components – turntables, tuners, tape deck etc. – allows the user to select which of these source signals is to be sent to the power amplifier, and adjust volume level for proper listening condition. All of these music source are low level signals : A full function preamp basically consist of a RIAA phono-stage, 10X gain ( i.e. 20dB ) line-stage and volume control, plus tape in-out facility. Phono cartridges have an output range from < 1mV up to only about several mV. Phono RIAA equalization of course is required, with a very heavy lifting phono-stage with at least 500 – 1,000 times amplification. Whereas tape decks & radio tuners are in the range of 500 mV output capability. Therefore the 10X line-stage is to provide the necessary additional amplification in order to boost all music source signal up to approx. 2V ( high level ) for adequate use with power amplifier』s input sensitivity. Also there maybe a buffer-stage before the preamp』s output -- it is to provide the preamp a low output impedance & drive long interconnects to power amplifier. In studio recording industry, the output-buffer-stage is essential for every preamp and console, because there are long cables used everywhere ! But if CD players are the main music source : this is a high level music source with output range from 2V upward -- this corresponds beautifully with todays poweramp 1.5 V – 2.0 V input sensitivities -- therefore further gain in preamp line-stage is not necessary. Tape deck or old fashioned turners are seldom used, whereas there are many stand alone phono-amps for use with LP players.
ASR – the ABC to understand EMITTER sound So we are unlikely to see a true 10X gain line-level pre-amplifiers on domestic hifi market today. In fact most modern preamps ( Line amp it is called ) only offer a 10dB gain, which is only about 1.5X gain for music signal from input to output ! Most of the time these preamp volume is set at 10-12 o』clock for normal listening, the source signal is not even amplified. This leaves the usable function of modern pre-amps to volume setting !
2) Apart from the necessary volume setting, what disadvantage or benefit (if any) if we still keep our preamps in the systems ?
In pursuit of high-fidelity reproduction : only disadvantage and no real benefit – unless the user has to use longer than usual interconnection cables. Shortest signal paths is the best -- the less component in between is the best. Every active circuit, electronics, would incur its own distortions, coloration and noise ! If it is not needed – why should it be there ?!
3) Can we replace the preamp with just a passive volume control for best sonic results, if no longer than usual interconnect cables are used ?
Unfortunately this is not the case. The reason is simple …. a passive volume-control introduces the fewest electronics in the signal path; theoretically it degrades the least and is extremely transparent. But most source components are designed to drive a relatively high input impedance, NOT the low input impedance of passive level controls ! The source component』s output impedance must be added to the passive control』s output impedance to find the total output impedance for driving the interconnect cables & poweramp. This total high output impedance causes high-frequency rolloff, particularly severe if relatively high-capacitance interconnects are used between passive control and poweramp. Now there are CD machines that incorporate a variable volume output, so life is getting a little better ! But beware ! |
|