新手上路
四星級會員
- 舊站積分
- 48
- 舊站發表文章數
- 2186
|
樓主 |
發表於 2009-6-15 22:01:11
|
顯示全部樓層
Re: CREEK 5350 SE (原廠網站資料)
原發表者是 ANDIO ART
[B]CREEK 5350 SE (原廠網站資料)

Made in UK!!
The Classic 5350SE evolved from one of the most popular amplifiers ever produced by Creek Audio – the 5350SE.
The Classic 5350SE is constructed in a modular way, with separate power amp, pre-amp and remote volume control circuit boards, connected with computer grade flat cables, plugs and sockets. It features a passive pre-amp circuit, providing no additional gain to the source signal. Although not strictly necessary, it can be configured with an active pre-amp if required, by plugging in an optional gain board which can be configured in steps of 3, 6 or 9 dB. An optional MM or MC Phono pre-amp can also be plugged in to further increase the flexibility of this fine integrated amplifier.
To accommodate Bi-wiring and Bi-amping, the Classic 5350SE is fitted with 2 pairs of high current speaker binding posts plus separate pre-amp output and power amp input sockets. Speaker A/B selection is switchable from the front panel. Joining and separating the pre/power sections is achieved with a switch on the rear panel, which is recessed to avoid accidental use. Typically this would be used when connecting an external device such as a subwoofer or graphic equaliser. The Classic 5350SE also hosts a front panel mounted headphone socket, which is unusual in modern integrated amplifiers.
Short circuit, DC offset and anti-thump protection circuitry makes the Classic 5350SE a sophisticated, user friendly integrated amplifier, with a technical performance close to the best that can be achieved.
For the technically minded, the Classic 5350SE uses a high current, N channel only, MOS-FET power output stage, driven by a P channel MOS-FET phase splitter and double differential voltage amplifier with symmetrical class A driver, to achieve ultra-low distortion and high speed with minimal negative feedback. Therefore, the Classic 5350SE is able to avoid using any active circuitry in its pre-amp and still achieve high input sensitivity. The optional plug-in gain board uses all discrete transistor circuitry in a unique double differential servo controlled design achieving unbelievably low distortion and noise performance.
The Classic 5350SE uses a 250VA toroidal transformer, together with multiple power supply capacitors totalling 31,000uF, 105 degree C, low impedance, to achieve the quality of computer grade capacitors but with very low inductance, for the ultimate in sonic performance.
Like other Creek amplifiers, the Classic 5350SE is DC servo controlled, to enable direct coupling from input to output and accurate low frequency roll-off, thereby eliminating sonically degrading capacitors from its signal path.
The Classic 5350SE remains a landmark in Hi-Fi design, incorporating state of the art circuitry with elegant styling to achieve a versatile and high fidelity amplifier par excellence.

兩組喇叭輸出(可做真正Biwe Bi Amp 連接)

可獨立操作前後級功能
Power in to 8Ohm
(both channels) > 90W
Power in to 4Ohm
(one channel) > 180W
Max current > 25 amps
THD
(total harmonic distortion) < 0.05% 20Hz - 20 KHz
Frequency Response 3Hz - 25KHz - 1dB
Power Amp Slew Rate > 50V per µs
Input Sensitivity 559mV for 90W
Signal to Noise Ratio > 105 dB
Separation > 60 dB
Remote control yes
Power Consumption at Idle < 40W
Power Consumption at Full Power 340W
Weight 7Kgs
Size W/H/D 430 x 70 x 280mm
輸出功率(兩聲道同時工作) >90W 8Ω
(一聲道工作) >180W 4Ω
最大電流 >25安培
總諧波失真(THD) <0.05% 20Hz-20kHz
頻率響應 3Hz~25kHz -1dB
迴轉率 >50V per μS
輸入靈敏度 620mV/50W
訊號雜音比 >105dB
分離度(高電平輸入/1kHz) >60dB
MM唱頭輸入靈敏度和阻抗(選用) 3.5mV47kΩ
MC唱頭輸入靈敏度和阻抗(選用) 0.75mV1kΩ
消耗功率(靜音) <40W
(滿功率) 340W
遙控器 全功能遙控
電源 115V-60Hz
重量 7公斤
尺寸 430x70x280mm
Stereophile A級榜上推薦 [/B]
[B]
+1 , 啟蒙小弟的綜擴,音樂性活潑,實在懷念.... [/B][/QUOTE]
[B]Destiny 擴大機
Destiny CD唱盤
EVO 綜合擴大機
EVO CD唱盤

Classic 5350SE 綜合擴大機
Classic CD唱盤
Classic Tuner調諧器
[/B]
|
|