忘記密碼
 立即註冊
樓主: hsindao

VTA

[複製鏈接]

3

主題

558

回帖

0

積分

新手上路

三星級會員

舊站積分
35
舊站發表文章數
558
發表於 2009-7-3 13:50:37 | 顯示全部樓層

Re: VTA

原發表者是 hsindao
[B]There are a few issues about VTA setting that I never quite understood.  Maybe some experts here can help me.  First, let's define VTA (Vertical Tracking Angle), SRA (Stylus Rake Angle) and VMA (Vertical Modulation angle).   VTA and SRA are common terminologies while VMA is the angle of how signals were cut in the vinyl.  The VMA picture came from here .

      

Questions:

1. What angle is VMA?  Obviously SRA should be the same as VMA.  Is it related to VTA?

2. When VTA was changed from 15 degree to 20 degree, and I guess the Vertical Cutting Angle of the cutter head might have been changed accordingly.  How does it affect VMA and thus SRA?

3. Treble tends to get enhanced when VTA is increased and became duller when VTA is decreased.  Why is that so?  What is the mechanism behind it?

4. Just for general discussion purpose, what do people listen for when adjusting VTA?  Some people I talked to said they could not quite tell the differences while some are very sensitive to it.  If you adjust VTA on every LP, how do you keep track of the current VTA after 2 weeks of vacation, for example? [/B]



This shows how SRA error ( to SMA) affects effective stylus size.
A Shibata tip can be the worst when SRA to SMA error getting larger.

26

主題

1689

回帖

100

積分

新手上路

四星級會員

舊站積分
3261
舊站發表文章數
1711
 樓主| 發表於 2010-4-17 07:42:13 | 顯示全部樓層

Fozgometer

Received May 2010 Stereophile today.  MF reviewed the Fosgate Fozgometer Azimuth Meter which answered my question about what does surround sound processor have to do with the azimuth meter:

"To measure channel separation and crosstalk, it uses a log-ratio detector developed for the steering-logic circuits of surround processors.  Fosgate says the readings are virtually independent of overall signal levels, and remain accurate over a variety of test signals."


To use it,

1. Play a mono test band from a test record.  The meter will read "0" and green center light will lit if channel output are equal.

2. Play a test signal with 1KHz in the left channel only.  Repeat with right channel only test.  Adjust azimuth so the reading are the same for L/R tests.

151

主題

8413

回帖

0

積分

新手上路

五星級會員

舊站積分
24833
舊站發表文章數
7074
發表於 2010-4-17 11:29:56 | 顯示全部樓層

Re: Fozgometer

Nice post.
But I do have other concerns about this product. Try to imaging that if we tighten the left screw of the cartridge mounting and let the right one not so tight and get the azimuth right with this meter. Will it sound differently if we tighten both screws and still get the meter right on? Or, say if we let both of the screws just a little bit more than holding the cartridge, will that be another sound out of the cartridge? I'd assume that this meter only addressed the voltage part of the game while missing the phase issue, that, seems to be the obscure and more difficult part of the audio world.

26

主題

1689

回帖

100

積分

新手上路

四星級會員

舊站積分
3261
舊站發表文章數
1711
 樓主| 發表於 2010-4-17 12:24:09 | 顯示全部樓層

Re: Re: Fozgometer

原發表者是 alc
[B]Nice post.
But I do have other concerns about this product. Try to imaging that if we tighten the left screw of the cartridge mounting and let the right one not so tight and get the azimuth right with this meter. Will it sound differently if we tighten both screws and still get the meter right on? Or, say if we let both of the screws just a little bit more than holding the cartridge, will that be another sound out of the cartridge? I'd assume that this meter only addressed the voltage part of the game while missing the phase issue, that, seems to be the obscure and more difficult part of the audio world.
[/B]

The problem you described has more to do with resonance than whether azimuth is set correctly or not.   Yes, it only measures voltage, and displays it in LOG scale.  

I have been thinking about a device to measure azimuth like this but the log scale converter, or a dbv meter, is something that I could not find.  Incidentally, the power meters of McIntosh amplifiers display power in log scale also.  Can anyone think of a way to use it to measure azimuth? []  

26

主題

1689

回帖

100

積分

新手上路

四星級會員

舊站積分
3261
舊站發表文章數
1711
 樓主| 發表於 2010-4-19 23:01:29 | 顯示全部樓層
Quiz.

1. What is the difference between aligning azimuth using instruments like the Fazgometer to measure minimum crosstalk, and the normal visual method by making sure the cantilever is vertical to the record surface?  Assuming that one has an excellent view of the cantilever.

2. If the stylus is not mounted vertically down on the cantilever, like the pictures shown.  How should one "visually" sets the azimuth?  Assuming that the stylus can be seen clearly, should we align by the angle of the stylus or the cantilever?  What are the trade-offs?

   

151

主題

8413

回帖

0

積分

新手上路

五星級會員

舊站積分
24833
舊站發表文章數
7074
發表於 2010-4-20 00:48:49 | 顯示全部樓層
Well, as long as they are quizes, I shall wait for the answers. []

Regardless what this forum is all about, I have more difficulties maintaining speakers alignment than the cartridge and stylus.  On my TNT, I have more problems maintaining the air bladders in a optimized pressure than that tiny dot of diamond. There are four of them, and I do hope that my own bladder won't become the fifth too soon.

26

主題

1689

回帖

100

積分

新手上路

四星級會員

舊站積分
3261
舊站發表文章數
1711
 樓主| 發表於 2010-4-21 06:21:50 | 顯示全部樓層
原發表者是 hsindao
[B]Quiz.

1. What is the difference between aligning azimuth using instruments like the Fazgometer to measure minimum crosstalk, and the normal visual method by making sure the cantilever is vertical to the record surface?  Assuming that one has an excellent view of the cantilever.


    [/B]


When aligning azimuth visually, we are trying to make sure that the stylus sits vertically in the groove.   When aligning azimuth using instruments to attain minimum crosstalk, we are aligning the angle of the coils so the R-ch coil would pick up least amount of L-ch modulation.

There will always be precision limit when components were put together so coils, cantilever, and stylus are not necessarily perfectly aligned.  Those 2 alignment methods will yield different results.

151

主題

8413

回帖

0

積分

新手上路

五星級會員

舊站積分
24833
舊站發表文章數
7074
發表於 2010-4-21 12:19:49 | 顯示全部樓層
Totally agreed.

Aligning Azimuth by ear is very subjective when considering that we count on the speakers for the judgment, yet the spacial relationship of the speakers in the room and the alignment error of them could affect seriously the result we try to get. And that part, in the end of the audio chain, is no less difficult to setup and achieve a good result than the front end.

But now I wonder what will we get from that smart device if we have a worn stylus to begin with or say, if we have a cantilevel or stylus mounting that is a few degrees off, will we get a "correct coil balance" while getting records worn? Or, we are not going to get a good result?

26

主題

1689

回帖

100

積分

新手上路

四星級會員

舊站積分
3261
舊站發表文章數
1711
 樓主| 發表於 2010-4-21 23:06:03 | 顯示全部樓層
原發表者是 alc
[B]

But now I wonder what will we get from that smart device if we have a worn stylus to begin with or say, if we have a cantilever or stylus mounting that is a few degrees off, will we get a "correct coil balance" while getting records worn? Or, we are not going to get a good result?
[/B]


There is nothing we can do about worn stylus.  A cantilever with stylus mounted a few degrees off is more common.  I encountered that twice.  The first one came with the Shure V15-IV.  I only noticed it near the end of the 1-year warranty and sent it back to Shure for replacement.  The 2nd time was a after market stylus for the same cartridge.  I noticed it only after purchasing a 20X loupe a few years later.  Both were off center by about 5 degrees.

Will a stylus mounted a few degree off center causes record damage?   Look at the micro ridge stylus pictures from Dynavector and mentally rotate the record groove by a few degrees.   My guess is not much.  I played those "bad" styli unwillingly for a few years and did not notice any groove damage.  It could also because I did not play each record that many times.

  

116

主題

2524

回帖

0

積分

新手上路

錄音刻片, 決定關鍵!!

舊站積分
2780
舊站發表文章數
2025
發表於 2010-12-15 13:28:47 | 顯示全部樓層
VTA 有必要常做微調嗎? 個人認為沒必要啦!!

調整對聲音會有改變, 包括 VTA微調. 主要因子調定位. 沒必要東調西整.  這裡多半是學理工的, 也多數在研發部門工作, 追根究底, 在所難免; 也無可厚非. 但是把輕鬆聽音樂的美事, 描繪得如同昔日考物理數學戰戰兢兢 (神經兮兮地); 聽音樂真得要這麼嚴肅嗎?  當然沒有必要.

輕輕鬆鬆地聽音樂才能達到欣賞音樂的樂趣.  

唱片的選購才是重點課題.

以下連結供大家參考.

http://www.n.mackie.btinternet.co.uk/documents/regaonvta.html
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-19 07:19 , Processed in 0.100717 second(s), 41 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表