忘記密碼
 立即註冊
樓主: P900

打造終極 HiEnd HTPC - 音樂重播新主義

[複製鏈接]

10

主題

109

回帖

0

積分

新手上路

一星級會員

舊站積分
5
舊站發表文章數
89
發表於 2008-9-13 12:26:46 | 顯示全部樓層
原發表者是 潛水艇
[B]以前電源供應器換成OCC線.........好累

[/B]


根據可靠消息來源(笑),現在有廠商開發發燒級的電腦PSU已經接近完成,包括電容、配線都按照音響標準來打造。我自認沒有潛水艇兄的耐性換線改機。我的做法是先弄出基本架構,供應器就不太計較,用一般的頂著等那顆PSU上市 []

190

主題

3241

回帖

200

積分

新手上路

四星級會員

舊站積分
2076
舊站發表文章數
2853
發表於 2008-9-14 17:22:40 | 顯示全部樓層

跟cMp作者Narsai的討論

跟他要source code準備自己踹看看,並共提了五個討論項目
工程人員的破英文只求達意,請見諒

Good ideas. Here's some feedback.

1.  cMP uses alternate USB ports that does not affect SQ. Mouse remote is better than IR remote. My initial design was to use something like WinLirc. Problem is the way serial comms work - there's continous polling which inteferes with SQ. Avoid it!

2.  Very interesting idea! Although no VGA card is used, video GPU operates off north bridge. Replacing VGA with a text based LCD (i.e.
very low on traffic) is brilliant.

3.  It would be nice if someone could test with XP SP2 Embedded...
Minlogon optimisation is from this XPE version.

4.  That's a very nice case but only supports mini-ITX boards. The Zalman TNN-300 PSU is externally mounted in door.

5.  Yes there's improvement here. Sonar has posted solutions as well (see cPlay thread).

Attached is cMP (which you must extract to folder 'cicsMemoryPlayer').
It's not pretty but it works for me. You may want to enhance it for DBCS (or unicode) and allow for different font sizes - I get lots of wishes for this.

Let me finish cPlay 1.2 thereafter, I'll make the source code available.

-----Original Message-----
Sent: 11 September 2008 04:56 AM
To: Narsai, Yatin
Subject: Audio Asylum: Feedback: The art of building Computer Transports


Dear Sir:

"The art of building Computer Transports" is the Bible of PC audio! I got more fantastic idea about improvement, hope your advice.

(1) Completly remove USB device:
    I check your guide and found there still have two usb1.1 devide 1.
Touch panel 2. wireless mouse.
    I got an idea to remove them all, we can use IR remote.
  
  We can employ COM PORT, and use SW like "IRCtrl、WinLIRC and Girder"

(2) Remove VGA card:
    It's a little bit difficult, but it's possible. We can use PRT port mono LCD, can write display code in your cMP/cPlay.
http://www.linuxfocus.org/English/September2002/article258.shtml

(3) Lite version XP
    As I know, there is a special XP named XPE.

(4) Heavy PC case:
    I check most PC case is thin than audio device,
    ZALMAN HD160XT 6.8kg/Origenae S21T 9.8kg/Origenae S16T 6.2kg (6mm)

This one is better:
http://atechfabrication.com/products/mini_server5x.htm

Or we can use power amplifier case.

(5) PSU modify:
    I have ask one diyer, he gave me an advice, we can use CLC/CRC circut to remove more ripple.

C = 1000uF, L = 2mH

   My friend tried to add CRC and use frequency analyser, and got very good improvement.


Really appricite your experience, it speeds up our progress!

At last, could you offer me sourec code of cMp/Cplay, I would like to try IR and LCD display.

Really thanks.

174

主題

8491

回帖

0

積分

新手上路

猩猩級會員

舊站積分
14228
舊站發表文章數
3171
發表於 2008-9-14 18:21:00 | 顯示全部樓層

Re: 跟cMp作者Narsai的討論

原發表者是 lwc
[B]跟他要source code準備自己踹看看,並共提了五個討論項目
工程人員的破英文只求達意,請見諒

Good ideas. Here's some feedback.

1.  cMP uses alternate USB ports that does not affect SQ. Mouse remote is better than IR remote. My initial design was to use something like WinLirc. Problem is the way serial comms work - there's continous polling which inteferes with SQ. Avoid it!

2.  Very interesting idea! Although no VGA card is used, video GPU operates off north bridge. Replacing VGA with a text based LCD (i.e.
very low on traffic) is brilliant.

3.  It would be nice if someone could test with XP SP2 Embedded...
Minlogon optimisation is from this XPE version.

4.  That's a very nice case but only supports mini-ITX boards. The Zalman TNN-300 PSU is externally mounted in door.

5.  Yes there's improvement here. Sonar has posted solutions as well (see cPlay thread).

Attached is cMP (which you must extract to folder 'cicsMemoryPlayer').
It's not pretty but it works for me. You may want to enhance it for DBCS (or unicode) and allow for different font sizes - I get lots of wishes for this.

Let me finish cPlay 1.2 thereafter, I'll make the source code available.

-----Original Message-----
Sent: 11 September 2008 04:56 AM
To: Narsai, Yatin
Subject: Audio Asylum: Feedback: The art of building Computer Transports


Dear Sir:

"The art of building Computer Transports" is the Bible of PC audio! I got more fantastic idea about improvement, hope your advice.

(1) Completly remove USB device:
    I check your guide and found there still have two usb1.1 devide 1.
Touch panel 2. wireless mouse.
    I got an idea to remove them all, we can use IR remote.
  
  We can employ COM PORT, and use SW like "IRCtrl、WinLIRC and Girder"

(2) Remove VGA card:
    It's a little bit difficult, but it's possible. We can use PRT port mono LCD, can write display code in your cMP/cPlay.
http://www.linuxfocus.org/English/September2002/article258.shtml

(3) Lite version XP
    As I know, there is a special XP named XPE.

(4) Heavy PC case:
    I check most PC case is thin than audio device,
    ZALMAN HD160XT 6.8kg/Origenae S21T 9.8kg/Origenae S16T 6.2kg (6mm)

This one is better:
http://atechfabrication.com/products/mini_server5x.htm

Or we can use power amplifier case.

(5) PSU modify:
    I have ask one diyer, he gave me an advice, we can use CLC/CRC circut to remove more ripple.

C = 1000uF, L = 2m

   My friend tried to add CRC and use frequency analyser, and got very good improvement.


Really appricite your experience, it speeds up our progress!

At last, could you offer me sourec code of cMp/Cplay, I would like to try IR and LCD display.

Really thanks. [/B]




P900冒著風雨,耗了整晚後
我們得到些小結論

1.lwc你現在要來踢館的話,不需帶機子過來
到時我會準備支鐵鎚,看你要當場砸我的PC,還是要帶回去自用

2.在XP動過手腳後,變成了很大器的聲音(很大器、很大器)
甚至,升頻後wav檔膨脹2.5倍,聲音也會大幅改變

3.PC訊源似乎還能不斷的進化…………
近日還會有小更動,到時再跟您報告
[/FOnt]

190

主題

3241

回帖

200

積分

新手上路

四星級會員

舊站積分
2076
舊站發表文章數
2853
發表於 2008-9-14 18:26:17 | 顯示全部樓層

Re: Re: 跟cMp作者Narsai的討論

除了1被否絕外,2,3,4,5在你的電腦上一樣都沒上,也就是說我的版本會多這四樣,鐵鎚留著自用吧~

原發表者是 martinon
[B]



P900冒著風雨,耗了整晚後
我們得到些小結論

1.lwc你現在要來踢館的話,不需帶機子過來
到時我會準備支鐵鎚,看你要當場砸我的PC,還是要帶回去自用

2.在XP動過手腳後,變成了很大器的聲音(很大器、很大器)
甚至,升頻後wav檔膨脹2.5倍,聲音也會大幅改變

3.PC訊源似乎還能不斷的進化…………
近日還會有小更動,到時再跟您報告
[/FOnt] [/B]

174

主題

8491

回帖

0

積分

新手上路

猩猩級會員

舊站積分
14228
舊站發表文章數
3171
發表於 2008-9-14 18:35:20 | 顯示全部樓層

Re: Re: Re: 跟cMp作者Narsai的討論

原發表者是 lwc
[B]除了1被否絕外,2,3,4,5在你的電腦上一樣都沒上,也就是說我的版本會多這四樣,鐵鎚留著自用吧~

[/B]



我也很期待
你的新計畫,能夠搞到何種光景
因為
經過前晚的調整,如果你還能有大躍進
真的很難想像,到時要算會被K掉的廠機
應該只能作…………………………負面表列
[/FOnt]

190

主題

3241

回帖

200

積分

新手上路

四星級會員

舊站積分
2076
舊站發表文章數
2853
發表於 2008-9-14 18:44:00 | 顯示全部樓層

Re: Re: Re: Re: 跟cMp作者Narsai的討論

剛查公司的mail才發現之前的案子曾有XPe的規畫,所以我有完整的kit,我再問看看能不能去外訓,假公濟私一下....

還能有大躍進啦~我連三件式的DCS苦主都找好了~~~所以還是得多下點苦工.
[]

原發表者是 martinon
[B]


我也很期待
你的新計畫,能夠搞到何種光景
因為
經過前晚的調整,如果你還能有大躍進
真的很難想像,到時要算會被K掉的廠機
應該只能作…………………………負面表列
[/FOnt] [/B]

49

主題

1552

回帖

0

積分

新手上路

四星級會員

舊站積分
32767
舊站發表文章數
1548
 樓主| 發表於 2008-9-15 19:44:45 | 顯示全部樓層
幾天不上myav 居然鐵鎚都上場了....

馬大現場的聲音真的很誇張 弄好一開聲也沒時間熱機 場面變的好大 沒聽過M30發出過那樣的聲音 如果沒現場聽到 實在很難相信音源會影響整體聲音這麼大 PC訊源潛力真的是有驚人的無限可能 更期待班長更上層樓 動員正規部隊和裝備的大計畫 能快點成功  如果CDP大廠聽到這樣的聲音 恐怕會重新思考新產品的發展方向

那天晚上風大雨狂 怕二高路況變化 沒時間等它熱機run in等聲音煮熟點 但是即便是匆匆聽幾個曲目 一般HTPC比較弱的氣勢和300HZ以下的聲音居然也非常完整的詮釋出來 而且是下沉而帶著力量去包覆整個聆聽空間 聽音樂在馬大的系統上真的很享受

謝謝馬大招待的狗咬豬和好久沒吃的鵝肉麵

174

主題

8491

回帖

0

積分

新手上路

猩猩級會員

舊站積分
14228
舊站發表文章數
3171
發表於 2008-9-16 12:52:38 | 顯示全部樓層
原發表者是 P900
[B]幾天不上myav 居然鐵鎚都上場了....

馬大現場的聲音真的很誇張 弄好一開聲也沒時間熱機 場面變的好大 沒聽過M30發出過那樣的聲音 如果沒現場聽到 實在很難相信音源會影響整體聲音這麼大 PC訊源潛力真的是有驚人的無限可能 更期待班長更上層樓 動員正規部隊和裝備的大計畫 能快點成功  如果CDP大廠聽到這樣的聲音 恐怕會重新思考新產品的發展方向

那天晚上風大雨狂 怕二高路況變化 沒時間等它熱機run in等聲音煮熟點 但是即便是匆匆聽幾個曲目 一般HTPC比較弱的氣勢和300HZ以下的聲音居然也非常完整的詮釋出來 而且是下沉而帶著力量去包覆整個聆聽空間 聽音樂在馬大的系統上真的很享受
[/B]



[!8] [!8]
老大
小弟受惠多多,在此公開跟您拜謝、拜謝

一套系統裡頭,到底是訊源, Amp, Speaker or 線材對聲音的影響最大
PC訊源對整體聲音的改變
委實出乎意料之外
所謂的〝Hi-end〞
在數位音樂的硬體上,或者在尋求新的solution
Boulder自家的CDP 1021,內建了2G flash ram來作buffer
自承用CD-rom的聲音勝過音響用的轉盤系統
而Cyrus的新CD,據說是當初Philips制訂CD規格的工程師參與開法
運用所謂Servo Evolution技術,用以改善CDP的讀取錯誤率
Linn自家開發的Klimax DS作為digital music player
也開始在自家網頁,販售數位音樂檔
naim出了台Naim CDX
2008的CES,Hovland也展出Music server的原型機
對於數位音樂的媒體、硬體的發展,一些Hi-end廠似乎漸漸有了共識…………………
[/FOnt]

14

主題

1079

回帖

0

積分

新手上路

三星級會員

舊站積分
78
舊站發表文章數
895
發表於 2008-9-16 20:53:54 | 顯示全部樓層
原發表者是 abysstw
[B]

根據可靠消息來源(笑),現在有廠商開發發燒級的電腦PSU已經接近完成,包括電容、配線都按照音響標準來打造。我自認沒有潛水艇兄的耐性換線改機。我的做法是先弄出基本架構,供應器就不太計較,用一般的頂著等那顆PSU上市 [] [/B]


等產品研發完成後, 請分享心得...[|)]

14

主題

1079

回帖

0

積分

新手上路

三星級會員

舊站積分
78
舊站發表文章數
895
發表於 2008-9-16 21:06:32 | 顯示全部樓層

Re: 跟cMp作者Narsai的討論

原發表者是 lwc
[B]跟他要source code準備自己踹看看,並共提了五個討論項目
工程人員的破英文只求達意,請見諒

Good ideas. Here's some feedback.

1.  cMP uses alternate USB ports that does not affect SQ. Mouse remote is better than IR remote. My initial design was to use something like WinLirc. Problem is the way serial comms work - there's continous polling which inteferes with SQ. Avoid it!

2.  Very interesting idea! Although no VGA card is used, video GPU operates off north bridge. Replacing VGA with a text based LCD (i.e.
very low on traffic) is brilliant.

3.  It would be nice if someone could test with XP SP2 Embedded...
Minlogon optimisation is from this XPE version.

4.  That's a very nice case but only supports mini-ITX boards. The Zalman TNN-300 PSU is externally mounted in door.

5.  Yes there's improvement here. Sonar has posted solutions as well (see cPlay thread).

Attached is cMP (which you must extract to folder 'cicsMemoryPlayer').
It's not pretty but it works for me. You may want to enhance it for DBCS (or unicode) and allow for different font sizes - I get lots of wishes for this.

Let me finish cPlay 1.2 thereafter, I'll make the source code available.

-----Original Message-----
Sent: 11 September 2008 04:56 AM
To: Narsai, Yatin
Subject: Audio Asylum: Feedback: The art of building Computer Transports


Dear Sir:

"The art of building Computer Transports" is the Bible of PC audio! I got more fantastic idea about improvement, hope your advice.

(1) Completly remove USB device:
    I check your guide and found there still have two usb1.1 devide 1.
Touch panel 2. wireless mouse.
    I got an idea to remove them all, we can use IR remote.
  
  We can employ COM PORT, and use SW like "IRCtrl、WinLIRC and Girder"

(2) Remove VGA card:
    It's a little bit difficult, but it's possible. We can use PRT port mono LCD, can write display code in your cMP/cPlay.
http://www.linuxfocus.org/English/September2002/article258.shtml

(3) Lite version XP
    As I know, there is a special XP named XPE.

(4) Heavy PC case:
    I check most PC case is thin than audio device,
    ZALMAN HD160XT 6.8kg/Origenae S21T 9.8kg/Origenae S16T 6.2kg (6mm)

This one is better:
http://atechfabrication.com/products/mini_server5x.htm

Or we can use power amplifier case.

(5) PSU modify:
    I have ask one diyer, he gave me an advice, we can use CLC/CRC circut to remove more ripple.

C = 1000uF, L = 2m

   My friend tried to add CRC and use frequency analyser, and got very good improvement.


Really appricite your experience, it speeds up our progress!

At last, could you offer me sourec code of cMp/Cplay, I would like to try IR and LCD display.

Really thanks. [/B]


期待實 踐 2-4 後心得分享.  請問是否有堅固且廉價一點 micro ATX的機箱介紹. 初步構想是做到完全無風扇, 以防振動. Zalmann HD160XT or HD160XT Plus 好, 不過貴.

如果能用 XPE 取代 XP SP2, 聲音可能能在上一層樓.  不知您有機會比較 XP 跟 Vista Enterprise 過嗎?  32 跟 64-bit OS 的差別?

Thanks.
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-19 12:30 , Processed in 0.111342 second(s), 41 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表