忘記密碼
 立即註冊
樓主: henryyyy

Mcintosh 俱樂部

[複製鏈接]

26

主題

1689

回帖

100

積分

新手上路

四星級會員

舊站積分
3261
舊站發表文章數
1711
發表於 2007-6-25 21:00:11 | 顯示全部樓層

Re: Re: 拜入7300??

原發表者是 ys_794639
[B]7300沒有Autoformer,一台7300接成Mono只是增加輸出功率,並不會因此提高電流推動能力,因為電流只是從一CH的NPN流到另一CH的PNP,輸出功率晶體是串聯而非並聯,問題是您習慣的聆聽音量曾讓7300破錶嗎?如果沒有,建議您省下這筆開銷,除非您想Bi-Amp! [/B]

MC7300 does contain autoformer.  The power rating is 300W for all output taps.

http://www.berners.ch/McIntosh/Downloads/MC7300_bro.pdf

26

主題

1689

回帖

100

積分

新手上路

四星級會員

舊站積分
3261
舊站發表文章數
1711
發表於 2007-6-25 21:22:00 | 顯示全部樓層
原發表者是 jjee68
[B]謝 ys_794639兄

mbl 101B本身低頻就不容易推
目前我也是用subwoofer來彌補

只是一想到可以讓喇叭的表現能再進一級
心理就不免希望再做一些補償

只是小弟對於器材不熟悉
對於您的熱情

在此答謝 [/B]

I have not heard MC7300 before.  However, I have used its predecessor MC7270 for a long time.   The MC7270 was not that good in getting the deep bass out of my Apogee speakers.  I doubt adding another MC7300 will help you that much in getting deep bass out of the MBL 101b.

The MC7300 likely has a gain setting in the back that you can set sensitivity for full output to 0.75V or 2.5V.  Which setting are you using?  If you are using McIntosh preamp,  the 2.5V will be the choice for most situations.  If you don't use McIntosh preamp, try 0.75V setting and use the volumn knob to adjust the best gain that goes with your preamp.  You can adjust the punch and sound stage with it.

9

主題

38

回帖

0

積分

新手上路

初級會員

舊站積分
3
舊站發表文章數
41
發表於 2007-6-25 22:13:24 | 顯示全部樓層
謝謝 hsindao 兄
我前級是用c37,目前設定0.75v
您的意思是將之調到2.5v?可以獲得低頻的改善嗎??
軟體比硬體重要許多多歐!!

9

主題

38

回帖

0

積分

新手上路

初級會員

舊站積分
3
舊站發表文章數
41
發表於 2007-6-25 22:17:07 | 顯示全部樓層
原發表者是 jjee68
[B]謝謝 hsindao 兄
我前級是用c37,目前設定0.75v
您的意思是將之調到2.5v?可以獲得低頻的改善嗎?? [/B]



所以你也不建議mono mono?
我以為會有很大的想像空間........[]
軟體比硬體重要許多多歐!!

26

主題

1689

回帖

100

積分

新手上路

四星級會員

舊站積分
3261
舊站發表文章數
1711
發表於 2007-6-26 00:05:40 | 顯示全部樓層
原發表者是 jjee68
[B]謝謝 hsindao 兄
我前級是用c37,目前設定0.75v
您的意思是將之調到2.5v?可以獲得低頻的改善嗎?? [/B]

Jjee68, the 2.5V/0.75V sensitivity means that MC7300 will output 300W with 2.5V or  0.75V input, respectively.  The 0.75V setting will have higher gain and will give you more punch and midrange.  The 2.5V setting will sound more relaxed and you may feel more bass because of recessed treble and midrange.  You will have to experiment with it, and the volumn knob, to see which setting works best in your system.  Do play with it though because you can get very different sound with those continously variable gain settings.

I have not heard mono-mono before but from people I trust, I think it will definitely an improvement.  The reason I did not enourage you to get a 2nd 7300, if your concern is getting more bass out of 101B, is because I think McIntosh power amps from the early 90s just can not deliver enough current in the low bass region.  When I replaced the MC7270 with 80W/ch Krell KSA-80B, there was tons more bass from the Apogee that I have never heard before.

I also use a REL Strata III subwoofer.   The REL can accept line level signal from preamp or high level signal from output of the power amp.  The REL works very well from the speaker output of the Krell.  The REL sounded slow connected to the MC7270 speaker output but far better if connected directly to the preamp  output.  This just shows that MC7270, and likely MC7300, is just fundamentally weak in the bass region if you have a low efficiency speaker.  I think you will get better result if you find a muscle amp like Krell or Gryphon if bass is the area that you want to improve.

Just a side note, I auditioned an MC352 at home once and compared it to the MC7270 side by side.  The MC352 has better bass but does not have the seductive midrange of the MC7270.  I would not trade 7270 for a 352.

9

主題

38

回帖

0

積分

新手上路

初級會員

舊站積分
3
舊站發表文章數
41
發表於 2007-6-26 08:15:02 | 顯示全部樓層
原發表者是 hsindao
[B]
Jjee68, the 2.5V/0.75V sensitivity means that MC7300 will output 300W with 2.5V or  0.75V input, respectively.  The 0.75V setting will have higher gain and will give you more punch and midrange.  The 2.5V setting will sound more relaxed and you may feel more bass because of recessed treble and midrange.  You will have to experiment with it, and the volumn knob, to see which setting works best in your system.  Do play with it though because you can get very different sound with those continously variable gain settings.

I have not heard mono-mono before but from people I trust, I think it will definitely an improvement.  The reason I did not enourage you to get a 2nd 7300, if your concern is getting more bass out of 101B, is because I think McIntosh power amps from the early 90s just can not deliver enough current in the low bass region.  When I replaced the MC7270 with 80W/ch Krell KSA-80B, there was tons more bass from the Apogee that I have never heard before.

I also use a REL Strata III subwoofer.   The REL can accept line level signal from preamp or high level signal from output of the power amp.  The REL works very well from the speaker output of the Krell.  The REL sounded slow connected to the MC7270 speaker output but far better if connected directly to the preamp  output.  This just shows that MC7270, and likely MC7300, is just fundamentally weak in the bass region if you have a low efficiency speaker.  I think you will get better result if you find a muscle amp like Krell or Gryphon if bass is the area that you want to improve.

Just a side note, I auditioned an MC352 at home once and compared it to the MC7270 side by side.  The MC352 has better bass but does not have the seductive midrange of the MC7270.  I would not trade 7270 for a 352. [/B]


謝謝前輩的指引
我將試著調整看看
感激!![]
軟體比硬體重要許多多歐!!

25

主題

552

回帖

0

積分

新手上路

三星級會員

舊站積分
111
舊站發表文章數
564
發表於 2007-6-26 09:44:42 | 顯示全部樓層

Re: Re: Re: Re: Re: 拜入7300??

原發表者是 jjee68
[B]mbl 101B本身低頻就不容易推
目前我也是用subwoofer來彌補
[/B]
哦!原來101b是MBL的叭,小弟對這家公司的叭有很深刻的印象,在一次音響展中看到他們家老闆,就問他他們家叭的工作原理,他也很直接地回覆了,原來他們家的叭也有音圈,只是音圈運動的方向是上下而非一般叭的前後運動,我想他們家叭的最大優勢是360度發聲吧,但是小弟對這樣的結構有幾點疑慮:

1. 他們把音圈放在單體下方而非上方,所以放mbl叭的地方最好注意一下不要有灰塵,否則經年累月下來,音圈&磁鐵間積了灰塵可是不好清理地。

2. 音圈去推動半月型振膜時,可以理解的是,上下兩端振幅大於中間,而聆聽者是聽中間發出的聲音,不知他們家叭的效率是否較低?

3. 以結構來看,他們家叭的中高音單體是裸露在外,沒裝音箱的。

小弟也一直斷斷續續地在玩Sub-Woofer,沒買過高檔貨,全都是DIY,所以可以亂搞,小弟的發言比較偏電路,所以沉得很快:

25

主題

552

回帖

0

積分

新手上路

三星級會員

舊站積分
111
舊站發表文章數
564
發表於 2007-6-26 09:45:39 | 顯示全部樓層

Re: Re: Re: 拜入7300??

原發表者是 hsindao
[B]MC7300 does contain autoformer.  The power rating is 300W for all output taps.
http://www.berners.ch/McIntosh/Downloads/MC7300_bro.pdf [/B]

謝謝,再看了一次7300的brochure,是的,它有Autoformer,小弟被它brochure上的Autotransformer可提供不是70.7V就是25V所迷惑,如造成jjee68兄困擾,在此致歉!

原發表者是 hsindao
[B]
Jjee68, the 2.5V/0.75V sensitivity means that MC7300 will output 300W with 2.5V or 0.75V input, respectively. The 0.75V setting will have higher gain and will give you more punch and midrange.   ~~恕刪~~
[/B]

0.75V的Gain應該是比較低,因為需要較高Vin,Gain = Vo / Vin

原發表者是 hsindao
[B]
I have not heard MC7300 before.  However, I have used its predecessor MC7270 for a long time. [/B]

很巧,小弟有一份7270完整Service Manual,它是用單差動電路,而現在200X則是並聯式雙差動電路,199X年代的Service Manual尚未蒐集到。

原發表者是 hsindao
[B]The reason I did not enourage you to get a 2nd 7300, if your concern is getting more bass out of 101B, is because I think McIntosh power amps from the early 90s just can not deliver enough current in the low bass region.  When I replaced the MC7270 with 80W/ch Krell KSA-80B, there was tons more bass from the Apogee that I have never heard before.
[/B]

先聲明沒有歧視的意思,每樣產品都有他的優缺點。
小弟覺得先天殘障的人(叭),再怎麼訓練(擴大機),最多參加殘障奧運,不要指望他打破正常人的紀錄!
先天殘障的定義,每個人不同!

26

主題

1689

回帖

100

積分

新手上路

四星級會員

舊站積分
3261
舊站發表文章數
1711
發表於 2007-6-26 10:40:44 | 顯示全部樓層

Re: Re: Re: Re: 拜入7300??

原發表者是 ys_794639
0.75V的Gain應該是比較低,因為需要較高Vin,Gain = Vo / Vin
[B] [/B]


Let's say full output voltage Vo = 75V.

At 0.75V sensitivity setting, Gain = 75/0.75 = 100

At 2.5V sensitivity setting, Gain = 75/2.5 = 30

小弟有一份7270完整Service Manual
[B] [/B]


Can I get a copy?  I still have the C34-V and MC7270 pair after 17 years, and still don't want to part with them.

先聲明沒有歧視的意思,每樣產品都有他的優缺點。
小弟覺得先天殘障的人(叭),再怎麼訓練(擴大機),最多參加殘障奧運,不要指望他打破正常人的紀錄!
先天殘障的定義,每個人不同!
[B] [/B]


I like to look at audio equipments this way:

Speakers are just like the appearance  of a person.  It is very easy to tell the difference.  Everyone has their own preference or standard for what beauty is.

Amplifiers are like the soul of a person.    One will have to live with it for sometime to appreciate it.  A system with a good soul will always be a long time companion.  You will hear what is right about the speakers.  On the other hand,  a system with good appearance but no soul will be just be like a bitch.  She may be exciting for a few days but then you will keep hearing what is wrong in the chain before it.

Source are like the brain.  It is the source that makes a system interesting.  A system with good soul and good look but without brain will be just like a dumb blond.  

People have been arguing which component is the most important part of a audio system.  It is like arguing whether brain, soul or the look is more important.

Back to your comment of "每樣產品都有他的優缺點", the art of audio is for the owner, like a chef, to balance the system so one will notice the best part of his system and ignore the 殘障 portion.

25

主題

552

回帖

0

積分

新手上路

三星級會員

舊站積分
111
舊站發表文章數
564
發表於 2007-6-26 11:57:46 | 顯示全部樓層

Re: Re: Re: Re: Re: 拜入7300??

小弟眼拙把2.5V看成0.25V

您住美國不妨直接跟McIntosh買Service Manual
之前小弟跟McIntosh買Service Manual
一份USD. 10~15
運費USD. 45
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-22 01:51 , Processed in 0.112836 second(s), 41 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表