忘記密碼
 立即註冊
查看: 1424|回覆: 6

關於 Groove echo

[複製鏈接]

151

主題

8413

回帖

0

積分

新手上路

五星級會員

舊站積分
24833
舊站發表文章數
7074
發表於 2009-11-15 12:37:06 | 顯示全部樓層 |閱讀模式
很清楚的解釋。 []

http://vinylville.tripod.com/groove-echo.html

The following is in reply to the original post, "Run-on groove
question", in the REC.MUSIC.COLLECTING.VINYL newsgroup. It seems that
most of us were pointed in the right direction with bits and pieces as
to the cause of, what is properly called, "groove echo". I called upon
a gentleman I have held in high regard for a long time... Bob Ludwig
took the time to explain, in detail, the causes of groove echo. In case
anyone is unfamiliar, Mr. Ludwig is a renown mastering and recording
engineer and executive for several established mastering labs and studios.
I'd like to thank him for his expertise and shedding some light on this
mystery. Here is his answer to the question, "What is the cause of groove
echo?"...


Dear Ken,

Here is a nice long answer to your question! I hope it helps! I've
enclosed a few pictures as well on another post to you.

Ghost In the Machine: groove echo in vinyl disks.

One of the great advantages of digital audio is that both vinyl records
and analog tape suffer from the transmission of sound from one recorded
layer of tape or record groove to the next. There is no cross-talk in
digital, it is only limited by the associated analog circuitry.

Groove echo, as it is called in the industry, is the result of a double
whammy. The first whammy occurs in the cutting process and the far worse
whammy occurs in the plating and even some in the pressing process.

When a groove is cut into a master acetate the grooves are purposely cut
as close to one another to maximize the recording time of the disk. The
RIAA recording curve is designed to greatly diminish the bass
frequencies so, while recording, the bass wiggles take up 400 times less
room than they would without the curve. On a good lathe, each rotation
of the lathe will result in the newly recorded part of the groove just
touching the previous rotations engraving. On the last state-of-the-art
lathes with computers (starting from about 1978) the newly recorded part
of the groove actually nestles into the previous rotation! The sound
of the deformed plastic of one revolution is probably always measurable
in the next and on some occasions is audible.

A newly recorded acetate is a joy to listen to. It is far, far quieter
than the final pressing (no matter whose vinyl formulation is used), it
is totally free of ticks and pops (until you touch it) and the groove
echo is very low.

The acetate is almost a living thing. How a lacquer electroplates is a
function of how well cured the lacquer is. The amount of oils in the
acetate are a function of how the manufacturer made it, how long it was
cured at the plant, and how long it was allowed to acclimatize to the
cutting room environment before cutting. After cutting, time starts to
act on the blank and the groove echo begins to build up within the
master lacquer. The first 24 hours are the most critical for avoiding
groove echo build-up. The idea is to get the lacquer into the plating
bath as quickly as possible.

Pop music is so limited in dynamic range that groove echo is rarely a
problem except in the lead-in and in-between bands. Classical music is
difficult to cut, plate and press. It is ideal to have the lathe in the
same building as the plating plant. The only East Coast pressing plant
that has this is Europadisk in NYC. In the hey-day of lacquer cutting
there were 2 independent electroplaters in NYC and they would have
messengers pick-up the lacquers from all the cutting houses in New York
every day.

Obviously sending lacquers by over-night delivery is less than ideal but
works well enough. Because of this groove-echo problem, lacquers were
rarely sent overseas to foreign licensees. This is why European cuts
were different from the American originals. The European cuts were
almost in every case cut from 15ips � inch Dolby noise-reduced tape
copies of the mastering done in America. Many aficionados of course feel
that anything European must de facto be better than the US but they were
always working from tape copies, as we did from their releases. With
digital masters for CDs and cassettes, this is no longer a problem,
merely send a clone overseas and every licensee puts out the exact same
product (except for countries like Japan where the record companies
almost add a bonus track to cut down on imports).

The plating process is where most of the groove echo was added. If the
bath the lacquer was put into for cleaning was too hot it would greatly
add to the echo problem. In the electroplating process there were
theories that the best plating had to be done very slowly and with the
lowest current possible to prevent groove echo. Once the first few
microns of nickel were set in place the intensity of the plating could
be greatly increased. Obviously when they were in a great rush they
would speed this process along. Test pressing were often rejected for
groove echo problems. The mastering engineer would often have to re-do
a lacquer and use the "echo" or "add land" facility on the lathe to
artificially spread the spacing between the grooves. On some classical
cuts, especially contemporary recordings, one can usually see with the
naked eye grooves spread-out before a big percussive attack.

DMM, Direct Metal Mastering in which the master disk is cut into copper
foil instead of acetate has far less groove echo problems because of the
much harder surface and because of eliminating the silvering process.
There still can be some however.

I hope this isn't more information that you ever wanted to know.
Enclosed are 3 jpg photos, one is the VMS-80 (Neumann) lathe at Gateway
Mastering. The next is the control panel on the lathe and finally a
close-up of the "add land" button that spreads the grooves out when one
pushes it to the degree set by the little wheel-knob under it!

Sincerely,
Bob Ludwig

167

主題

8萬

回帖

0

積分

新手上路

五星級會員

舊站積分
32767
舊站發表文章數
11966
發表於 2009-11-15 17:03:10 | 顯示全部樓層
Groove echo 本來就很嚴重啊!!

下一段樂曲,如果一開始就很大聲

你在它的前一圈就聽得到了

但你又能怎麼辦呢??

We can do nothing about it

[8D] [8D] [8D]

151

主題

8413

回帖

0

積分

新手上路

五星級會員

舊站積分
24833
舊站發表文章數
7074
 樓主| 發表於 2009-11-15 20:59:01 | 顯示全部樓層
政治問題也很嚴重啊,一樣不能怎麼樣,可也有人喜歡提,我這種無聊當有趣算小咖的啦! []

26

主題

1689

回帖

100

積分

新手上路

四星級會員

舊站積分
3261
舊站發表文章數
1711
發表於 2009-11-16 11:17:49 | 顯示全部樓層
Good stuffs.  +3.  I wonder if spring-back happen at the same rate as pre-echo forming.  The amount of spring-back may also depend on how quickly the electroplating process took place and be part of the reasons why small SRA adjustment is needed from record to record.

167

主題

8萬

回帖

0

積分

新手上路

五星級會員

舊站積分
32767
舊站發表文章數
11966
發表於 2009-11-16 13:50:45 | 顯示全部樓層
原發表者是 hsindao
[B]Good stuffs.  +3.  I wonder if spring-back happen at the same rate as pre-echo forming.  The amount of spring-back may also depend on how quickly the electroplating process took place and be part of the reasons why small SRA adjustment is needed from record to record. [/B]


一個聲道是 pre-echo

另一個聲道就是 spring-back

大小應該是一樣的

或可稱之為相鄰 groove 之間的 crosstalk

[] []

26

主題

1689

回帖

100

積分

新手上路

四星級會員

舊站積分
3261
舊站發表文章數
1711
發表於 2009-11-16 21:51:35 | 顯示全部樓層
原發表者是 wecare
[B]

一個聲道是 pre-echo

另一個聲道就是 spring-back

大小應該是一樣的

或可稱之為相鄰 groove 之間的 crosstalk

[] [] [/B]

Huh?

Maybe you can answer this question first.  Why do we hear pre-echo at the beginning of a track and not post-echo at the end of a track?

167

主題

8萬

回帖

0

積分

新手上路

五星級會員

舊站積分
32767
舊站發表文章數
11966
發表於 2009-11-16 22:07:08 | 顯示全部樓層
原發表者是 hsindao
[B]
Huh?

Maybe you can answer this question first.  Why do we hear pre-echo at the beginning of a track and not post-echo at the end of a track? [/B]


平地一聲雷

與暴雨忽然停止後的細雨

感受當然不同

[] []
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-19 00:52 , Processed in 0.109442 second(s), 37 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表