忘記密碼
 立即註冊
查看: 117|回覆: 3

清售:crown MT600 後級擴大機 $20000

  [複製鏈接]

64

主題

14

回帖

0

積分

新手上路

一星級會員

舊站積分
0
舊站發表文章數
62
發表於 2003-12-24 09:48:22 | 顯示全部樓層 |閱讀模式
power:120V/60Hz 重量:16.5kg

53

主題

843

回帖

0

積分

新手上路

三星級會員

舊站積分
0
舊站發表文章數
890
發表於 2003-12-24 10:04:41 | 顯示全部樓層
Stereo Power Lead: 325W-4/220W-8/400W-2 Mono Power Lead: 750W-4 Dimensions: 19 x 3.5 x 16" 2 rack space USD:599.http://www.proaudiodesign.com/productinfo.php?ItemID=P3156

53

主題

843

回帖

0

積分

新手上路

三星級會員

舊站積分
0
舊站發表文章數
890
發表於 2003-12-24 10:07:28 | 顯示全部樓層
Stereo Power Lead: 325W-4歐母/220W-8歐母/400W-2歐母 Mono Power Lead: 750W-4歐母Dimensions: 19 x 3.5 x 16" 2 rack space
美金售價USD:599.

53

主題

843

回帖

0

積分

新手上路

三星級會員

舊站積分
0
舊站發表文章數
890
發表於 2003-12-24 10:11:12 | 顯示全部樓層
Architects' and Engineers' Specifications for
MT-600



Architects Specifications

Micro-Tech 600 (120 V, 60 Hz models)

The power amplifier shall be a solid-state two-channel model employing multi-mode (AB+B) grounded bridge(TM) output circuitry.

The outputs shall be switchable as stereo, bridged-mono or parallel-mono modes of operation. The bridged-mono mode shall bridge the outputs to provide increased output voltage. The parallel-mono mode shall parallel the outputs to provide increased output current.

The output impedance of each channel shall be less than 10 milliohms in series with less than 2 microhenries in stereo mode.

The amplifier shall contain protection circuitry which limits the drive level placed on the output devices before their SOA (Safe Operating Area) is exceeded. This protection circuitry shall calculate the instantaneous voltage across and current through the output devices while factoring in their simulated junction temperatures to predict how close they are to their operating limits. This protection will be called "ODEP."

The amplifier shall contain controlled slew-rate voltage circuitry to protect it against radio frequency interference burnouts. It shall also be protected from current overload at its output stage. The slew rate of the amplifier shall be greater than 13 volts per microsecond in stereo mode.

The amplifier shall temporarily go into a stand-by mode if its power transformer becomes excessively hot and shall automatically resume normal operation once it has cooled to a safe operating temperature.

Front-panel controls shall include an enable on/off switch.

Rear-mounted controls shall include a ground lift switch to isolate the signal ground from the chassis ground, a switch which selects between stereo, bridged-mono and parallel-mono modes of operation, a gain control for each channel, and two push-button reset switches to reset the circuit breakers for the high-voltage power supplies.

Internal controls shall include an input sensitivity switch to select between 0.775 V, 1.4 V or a fixed voltage gain of 26 dB for full rated output.

Front panel indicators shall include an amber power enable indicator and an amber protection system indicator (ODEP) for each channel which shall normally be illuminated to confirm the availability of reserve thermodynamic energy and which shall dim in proportion to limiting when the power demands of the output stages have been exceeded.

The power amplifier shall meet or exceed the following performance criteria. Input sensitivity for rated output: 26 dB voltage gain (unbalanced). Rated FTC output in stereo mode with less than 0.1% THD: 285 watts per channel (20 Hz to 20 kHz) into 4 ohms; 210 watts per channel (20 Hz to 20 kHz) into 8 ohms. Rated FTC output in bridged-mono mode with less than 0.1% THD: 670 watts (20 Hz to 20 kHz) into 8 ohms; 420 watts (20 Hz to 20 kHz) into 16 ohms. Hum and noise: at least 105 dB (A weighted) below full rated output power. Phase response: 10 degrees from 10 Hz to 20 kHz at 1 watt. Frequency response: 20 Hz to 20 kHz, 0.1 dB at 1 watt into 8 ohms per channel in stereo mode. Damping factor: greater than 1000 from 10 to 400 Hz into 8 ohms. Intermodulation distortion (SMPTE): less than 0.05% from 163 milliwatts to rated power into 8 ohms in stereo mode. Harmonic distortion at rated power into 8 ohms per channel (stereo mode): less than 0.05% from 20 Hz to 1 kHz and increasing linearly to less than 0.1% at 20 kHz.

The amplifier shall be safe when driving any kind of loadeven highly reactive ones.

The power requirements shall be 120 VAC at 60 Hz. At idle, the amplifier shall draw 100 watts or less.

The amplifier chassis shall be constructed of steel with a durable black finish and shall be designed for flow-through fan-assisted ventilation from the front panel to the side panels. The amplifier shall have an aluminum front panel with Lexan overlay and air filter media.

The dimensions of the amplifier shall allow for 19 inch (48.3 cm) EIA standard (RS-310-B) rack mounting. The amplifier shall be 3.5 inches (8.9 cm) tall and 16 inches (40.6 cm) deep behind the rack-mounting surface.

The amplifier shall weigh 36 pounds, 4 ounces (16.5 kg) and shall have a center of gravity approximately 6 inches (15.2 cm) behind the front panel.

The amplifier shall be designated the Crown Micro-Tech 600.
您需要登錄後才可以回帖 登錄 | 立即註冊

本版積分規則

Archiver|MyAV視聽商情網 test

GMT+8, 2026-11-21 07:11 , Processed in 0.140792 second(s), 31 queries .

Powered by MyAV!

快速回覆 返回頂部 返回列表